Husqvarna 1130SB-LSB 532 18 00-82 Intermediate Gear, Clevis PIN, 532 17 53-44 Trunnion Bearing

Page 34

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

		24
		23							1	2
	27		21						3
			21					28	1	1
								28	1
	25
	25	27		28			2
							2
						14
										16


		22						142	1
			2					142	3
		26	2	2				13	15
			1					13
	28
		28
		28	2						2
			2					14	2
								14
						3	2		20
			12		1	3	2
					1

							17	18
		11					17
	8	11
8	8								19
									19
		10
		10
		9

				8
	4			7
	4			5
1	4			5
1				6
				6
			5	01.02.001-F_Sheet_1
2		3	4
2
	1

KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	817 49 05-08 BOLT 5/16−18 X .500		15	532 18 00-82 INTERMEDIATE GEAR
2	532 75 11-53	NUT 5/16−18	16	532 18 01-34 AUXILIARY SHAFT
3	532 18 00-17 FLANGE BEARING		17	532 40 54-85 CONTROL ARM
4	873 93 05-00	NUT 5/16−18	18	532 05 70-79	WASHER
5	532 19 95-09 RUBBER WHEEL PLATE		19	532 40 61-09 CONTROL SHAFT ASSEMBLY
6	532 17 98-31 RUBBER WHEEL RING		20	532 19 85-80	CLEVIS PIN
7	532 17 86-13 RUBBER WHEEL HUB		21	532 18 40-80 SHIFTER LEVER
8	874 76 05-14 BOLT 5/16−18 X .875		22	532 18 78-57 PIVOT BRACKET
9	532 17 53-44 TRUNNION BEARING		23	532 17 88-07	PIVOT PIN
		ASSEMBLY	24	532 18 01-35	SPRING
10	812 00 00-12	RETAINER	25	532 18 71-01	SHIFTER LINK
11	532 18 00-66	HEX SHAFT	26	532 08 51-79	RETAINER
12	532 18 00-65	PINION GEAR	27	532 70 02-79	CLIP
13	532 19 29-07 AUXILIARY PLATE		28	817 00 05-12 BOLT 5/16−18 x .750
14	532 17 92-70 SPACER PLATE

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 34

Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles POP Rivet 1/8 Lower Tube Gray Pivot Support532 18 77-16 Shifter ROD Bottom 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Clutch ROD532 17 86-66 Halogen Headlight Grip Switch532 42 14-48 Headlight Bezel Gray BulbDrive 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly HEX ShaftClevis PIN Assembly532 18 00-82 Intermediate Gear 532 17 53-44 Trunnion BearingGear Axle ShaftRoll PIN 3/16 Clik PINClutch Slide CoverWheel Lobe Axle LobeBottom PAN Chassis / Engine / PulleysFrame Engine Mount PlatePulley Impeller BeltWheels 532 19 30-71 Safety Ignition KEY Repair PartsPower Cord Retainer PINDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement