Husqvarna 1130SB-LSB Operation, Know Your Snow Thrower, Primer, Ignition KEY, Pull OUT to Stop

Page 8

OPERATION

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning.

DANGER

 

 

 

PRIMER

 

 

OR WARNING

READ AND FOLLOW ALL SAFETY INFORMATION

AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT. FORWARD REVERSE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IGNITION KEY.

 

INSERT TO START

 

AND RUN,

 

PULL OUT TO STOP.

 

DISENGAGED

ENGAGED

 

SNOW

TRACTION

DISCHARGE

DRIVE CONTROL

 

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine If Recoil Starter has Frozen To Start EngineBefore Stopping Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Skid Plate Auger Assembly 30 LHAuger Assembly 30 RH 01.16.001-A Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 Lower Tube Gray Pivot Support532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch RODGrip Switch 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight BulbDrive 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment HEX ShaftAssembly 532 18 00-82 Intermediate GearClevis PIN 532 17 53-44 Trunnion BearingAxle Shaft Roll PIN 3/16Gear Clik PINCover Wheel LobeClutch Slide Axle LobeChassis / Engine / Pulleys FrameBottom PAN Engine Mount PlatePulley Impeller BeltWheels Repair Parts Power Cord532 19 30-71 Safety Ignition KEY Retainer PIN532 18 37-30 DECAL, Remote Deflector DECAL, Husq 532 18 10-35 DECAL, DANGER, DeflectorDECAL, Husq Service Notes Service Notes Warranty Statement
Top Page Image Contents