Husqvarna 1130SB-LSB owner manual Repair Parts, Power Cord, Retainer PIN, Wrench

Page 40

REPAIR PARTS						BAG OF PARTS
SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38
	4
14			6 7	KEY	PART
13	5		6 7	KEY	PART
12	5			NO.	NO.	DESCRIPTION
				NO.	NO.	DESCRIPTION
			9
		8	9	1	532 19 85-63	POWER CORD
		8		1	532 19 85-63	POWER CORD
				2	532 16 96-75	RETAINER PIN
				3	532 18 06-84	WRENCH
3			10 11	4	532 18 45-05 REMOTE SPRING
3			10 11	5	532 17 98-29 SHOULDER BOLT 1/4−20
				6	532 17 92-46 NYLON WASHER 1/4−20
				7	532 19 17-30 LOCKNUT 1/4−20
				8	872 25 05-05 CARRIAGE BOLT 5/16−18 X 5/8
				9	532 75 11-53 LOCKNUT 5/16−18
				10	873 80 06-00 LOCKNUT 3/8−16
				11	819 13 13-16	WASHER 3/8
				12	532 19 86-36 SHEAR BOLT 1/4−20 X 1−3/4
				13	532 19 86-38	SPACER
				14	873 80 04-00 LOCKNUT 1/4−20
2			1
			1
			01.14.003-A

1	KEY	PART	DESCRIPTION
	NO.	NO.
01.14.007-A	1	532 19 30-71 SAFETY IGNITION KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 40

Image 40

Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 Lower Tube Gray Pivot Support532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch RODGrip Switch 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight BulbDrive 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment HEX ShaftAssembly 532 18 00-82 Intermediate GearClevis PIN 532 17 53-44 Trunnion BearingAxle Shaft Roll PIN 3/16Gear Clik PINCover Wheel LobeClutch Slide Axle LobeChassis / Engine / Pulleys FrameBottom PAN Engine Mount PlatePulley Impeller BeltWheels Repair Parts Power Cord532 19 30-71 Safety Ignition KEY Retainer PINDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement

REPAIR PARTS

BAG OF PARTS

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

KEY

POWER CORD

RETAINER PIN

WRENCH

WASHER 3/8

KEY

532 19 30-71 SAFETY IGNITION KEY