Husqvarna 1130SB-LSB Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

1/4-20

SPRING

CHUTE

SHOULDER

DEFLECTOR

BOLT

 

 

HOOK

NYLON

BETWEEN

WASHER

HEX NUTS

 

ON CHUTE

1/4-20

ROTATER

LOCKNUT

HEAD

 

5/16-18

 

CARRIAGE

 

BOLT

CABLE

 

EYELET

 

REMOTE

 

CABLE

 

BRACKET

 

5/16-18

 

LOCKNUT

 

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

7

Image 7
Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigBefore Starting the Engine Before Stopping To Start EngineIf Recoil Starter has Frozen Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate 01.16.001-A 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 Pivot Support Lower Tube GrayClutch ROD 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly 532 18 77-16 Shifter ROD BottomBulb Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightDrive HEX Shaft 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate Weldment532 17 53-44 Trunnion Bearing Assembly532 18 00-82 Intermediate Gear Clevis PINClik PIN Axle ShaftRoll PIN 3/16 GearAxle Lobe CoverWheel Lobe Clutch SlideEngine Mount Plate Chassis / Engine / PulleysFrame Bottom PANImpeller Belt PulleyWheels Retainer PIN Repair PartsPower Cord 532 19 30-71 Safety Ignition KEYDECAL, Husq DECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement