Husqvarna 1130SB-LSB owner manual 01.16.001-A

Page 24

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38

1

1

	3		2
	3
	4
5		4	3
			3

3 4 5

2

3

4

01.16.001-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 18 47-47 DRIFT CUTTER BAR

2872 27 05-06 CARRIAGE BOLT 5/16−18 X .750

3532 17 92-46 PLASTIC WASHER

4810 04 05-00 LOCKWASHER 5/16

5	532 12 86-38 NUT 5/16−18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 24

Image 24

Contents 1130SB-LSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Before StoppingIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 30 LH Auger Assembly 30 RHSkid Plate 01.16.001-A Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 Lower Tube Gray Pivot Support532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD Assembly532 18 77-16 Shifter ROD Bottom Clutch RODGrip Switch 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight BulbDrive 532 19 84-74 Speed Selector Head Assembly Trunnion Bearing Assembly532 19 77-63 Drive Plate Weldment HEX ShaftAssembly 532 18 00-82 Intermediate GearClevis PIN 532 17 53-44 Trunnion BearingAxle Shaft Roll PIN 3/16Gear Clik PINCover Wheel LobeClutch Slide Axle LobeChassis / Engine / Pulleys FrameBottom PAN Engine Mount PlatePulley Impeller BeltWheels Repair Parts Power Cord532 19 30-71 Safety Ignition KEY Retainer PINDECAL, Husq 532 18 10-35 DECAL, DANGER, Deflector DECAL, Husq532 18 37-30 DECAL, Remote Deflector Service Notes Service Notes Warranty Statement