Ariens 932505 - 724, 932038 - 5520, 932037 - 724 To Stop in AN Emergency, Starting and Shut OFF

Page 16

4. Adjust Runners

Check and adjust Runners (see Service and Adjustments). Allow 1/8 in. (3 mm) between scraper blade and hard, smooth surface(s). Allow 1-1/4 in. (30 mm) between scraper blade and uneven or gravel surfaces.

5. Check Engine Fuel & Crankcase Oil

WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding.

Check and add fuel if required. Check that the engine crankcase oil is full using dipstick. Refer to Engine Manual for detailed instructions.

TO STOP IN AN EMERGENCY

Immediately release both control bails to stop unit in an emergency. Stop engine, remove key and wait for all rotating parts to stop before leaving operator’s position.

STARTING AND SHUT OFF

WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. DO NOT attempt to start your unit at this time. Read entire Owner/ Operator Manual and the Engine Manual first.

IMPORTANT: Allow unit and engine to adjust to the outdoor temperatures before clearing snow. Before shut-off, run the attachment a few minutes to prevent freeze-up.

NOTE: Try out each control without the engine running to see how it works and what it does.

Manual Start

1.Turn discharge chute straight ahead.

2.Make sure that the traction clutch and attachment drive clutch bails are fully disengaged.

3.Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.

4.If engine is cold, apply choke. See Engine Manual for detailed instructions.

NOTE: A warm engine requires less choking than a cold engine.

5.Set throttle to proper starting position.

6.Insert key into ignition switch and push into RUN position. DO NOT twist key after it is inserted.

7.Grasp starter handle and pull rope out slowly until it pulls harder. Let rope rewind slowly.

8.Pull rope with a rapid continuous full arm stroke. Let rope rewind slowly.

IMPORTANT: DO NOT let Starter Handle snap against Starter.

9.Repeat steps 7 and 8 until engine starts. (If engine does not start, refer to Troubleshooting.)

10.Adjust choke as needed.

11.Set throttle to Part Throttle or Slow position for adaptation to outside temperature or travel. Set throttle to Fast position for normal operation.

Electric Start (932037, 038, 039)

1.Connect extension cord to prongs on starter.

IMPORTANT: Prevent damage to unit. Know voltage of your starter and only use matching outlets.

2.Plug extension into 120V 3-wire, grounded outlet.

3.Turn discharge chute straight ahead.

4.Make sure that the traction clutch and attachment drive clutch bails are fully disengaged.

5.Push Primer Bulb 2 or 3 times for cold engine.

NOTE: When temperature is below -15° F (-26° C) additional priming may be needed.

6.Insert key into ignition switch on engine and push into "Run" position. DO NOT twist key after it is inserted.

7.If engine is cold, apply choke. A warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions.

8.Set throttle to proper starting position.

9.Press starter button on engine until engine starts.

IMPORTANT: DO NOT operate starter more than 15 seconds per minute, as overheating and damage can occur. (If engine does not start, refer to Troubleshooting.)

10.Adjust choke as needed.

11.Disconnect power cord from outlet, then starter.

12.Set throttle to Part Throttle or Slow position for adaptation to outside temperature or travel. Set throttle to Fast position for normal operation.

GB - 16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Sno-Thro Handgeführte Schneefräse Spazzaneve Semovente ’opérateur Vibrationswerte An den Händen Table of Contents IntroductionSafety Safety Decals Locations Required Operator TrainingSafety Rules Do not allow adults to operate unit without proper trainingPage Assembly AssemblyTools Required Unfold Handlebar Figure932507 932037, 039, 505 Discharge Chute Check Tire PressureCheck Auger Gearcase Oil Check Engine Crankcase OilControls and Features Controls and Features OperationSnow Clean-Out Tool ThrottleElectric Starter Recoil Starter HandleFilling Fuel Tank PRE-STARTTo Stop in AN Emergency Starting and Shut OFFMaintenance Service PositionTraveling Snow RemovalMaintenance Schedule Service and Adjustments General LubricationDischarge Chute Deflector Discharge ChuteSpeed Selector Adjustment For ReplacementRunners Scraper BladeAttachment Drive Belt Replacement Remove Attachment Drive BeltReplace Attachment Drive Belt Important Belt Finger Must beTraction Drive Belt Replacement Attachment CLUTCH/BRAKE AdjustmentTraction Drive Clutch Adjustment Friction Disc Replacement Remove Friction DiscReinstall Friction Disc StorageShort Term Long TermAccessories Service PartsTroubleshooting Does not OperateForward ReverseSpecifications Size and WeightYear Limited Sno-Thro Warranty
Related manuals
Manual 31 pages 47.91 Kb

932508 - 624, 932505 - 724, 932507 - 520, 932039 - 624, 932037 - 724 specifications

Ariens has long been celebrated for its commitment to quality and durability in outdoor power equipment, and the Ariens 932038, 932507, 932039, 932505, and 932508 models are a testament to that legacy. These snow blowers offer a blend of robust performance, advanced technology, and user-friendly features that make them essential for managing winter weather.

The Ariens 932038 model stands out with its 5520 engine, delivering dependable power designed to tackle heavy snowfalls. Its 24-inch clearing width ensures efficient snow removal, while the high-quality, heavy-duty construction guarantees long-lasting performance. Equipped with an adjustable auger, the 932038 can handle a variety of snow conditions, making it versatile for different scenarios.

Similarly, the 932507 model, featuring a powerful 520cc engine, provides significant clearing capabilities. Users will appreciate the 24-inch clearing width and the ability to throw snow up to 50 feet. The unique design includes oversized tires that enhance traction and maneuverability, ensuring users can confidently navigate through driveways and pathways even in deep snow.

The Ariens 932039 model, powered by the 624cc engine, takes snow removal a step further. This powerful machine's 26-inch clearing width allows for faster snow processing, and its auto-turn steering technology provides effortless handling around obstacles, a critical feature for those with tight driveways or pathways.

With the 932505 model, users can utilize the 724cc engine, making it one of the more powerful options in this lineup. Its 28-inch clearing width couples with an advanced impeller system that maximizes snow throwing distance, making it perfect for large areas. Additionally, the heated handgrips improve comfort during prolonged use in frigid conditions.

Finally, the Ariens 932508, equipped with a 624cc engine, combines strength with ease of use. Its user-friendly control panel and electric start feature provide convenience, making it ideal even for those less experienced with snow blowers. The combination of a 26-inch clearing width ensures efficient snow removal, while the durable construction promises longevity.

Each of these Ariens models comes with a host of features designed for efficiency. From adjustable speed settings to high-impact and rust-resistant materials, these machines are built to withstand the rigors of winter. Whether facing light snow or heavy drifts, the Ariens 932038, 932507, 932039, 932505, and 932508 snow blowers deliver the reliability and performance users expect, ensuring that winter does not hinder outdoor activities.
Top Page Image Contents