Storage, Short Term, Long Term | Ariens 932039 - 624, 932038

9.Reinstall one nut to keep the inside bearing cap in place.

10.Remove bearing cap/bushing and washer from right side of unit.

11.Reinstall nuts on screws through side frame to keep screws in place.

12.Slide friction disc assembly and hex shaft to the right until the left end of shaft is clear of left bearing. Tap lightly if necessary, to loosen. The shaft slides out of the small pinion gear and washer.

13.Carefully lift shaft and friction disc out of unit. As you remove the assembly, the washers between the bearing and sliding forks will be loose. Do not lose the washers.

Replace Friction Disc

1.Remove three (3) hex bolts and nuts holding friction disc to shift carrier.

2.Remove the old friction disc. Put the new friction disc in place, flat side to the shift carrier.

3.Reinstall the three (3) bolts and nuts into the new friction disc and hub. Torque to 5-6 lbf-ft (6.8 to 8.13 N•m).

Reinstall Friction Disc

1.Reinstall the shift carrier, the small pinion gear and washer onto the hex shaft. The washer goes between the bearing and the pinion gear.

2.Slide the shaft and attached parts into the frame, through the right side hole first, then the left. Pinion gear must mesh with the large gear.

3.Reinstall the flange bearing and washers into the shift forks. Be sure the washers are inside the forks.

4.Reinstall the bearing and outside bearing cap on the left side of the frame.

5.On the right side of the frame, place the washer on the end of the shaft.

6.Reinstall the bearing cap/bushing on the right side of frame.

7.Reinstall roll pins in shaft. Be sure pins are centered in shaft.

8.Reinstall shift rod with hairpin and washer.

9.Reinstall tires with lockpins.

10.Install bottom cover.

11.Set unit upright.

12.Replace spark plug wire on spark plug.

STORAGE

WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding.

SHORT TERM

IMPORTANT: NEVER spray unit with high pressure water or store unit outdoors.

Run with attachment clutch engaged a few minutes after each use to free unit of any loose or melting snow.

Close fuel shut-off valve.

Inspect unit for visible signs of wear, breakage or damage.

Keep all nuts, bolts and screws properly tightened and know unit is in safe working condition.

Store unit in a cool, dry protected area.

LONG TERM

Clean unit thoroughly with mild soap and low pressure water and lubricate (see Maintenance). Touch up all scratched painted surfaces.

Remove weight from wheels by putting blocks under frame or axle.

When storing unit for extended periods of time, remove all fuel from tank and carburetor (run dry). Refer to Engine Manual.

GB - 26

932508 - 624, 932505 - 724, 932507 - 520, 932039 - 624, 932037 - 724 specifications

Ariens has long been celebrated for its commitment to quality and durability in outdoor power equipment, and the Ariens 932038, 932507, 932039, 932505, and 932508 models are a testament to that legacy. These snow blowers offer a blend of robust performance, advanced technology, and user-friendly features that make them essential for managing winter weather.

The Ariens 932038 model stands out with its 5520 engine, delivering dependable power designed to tackle heavy snowfalls. Its 24-inch clearing width ensures efficient snow removal, while the high-quality, heavy-duty construction guarantees long-lasting performance. Equipped with an adjustable auger, the 932038 can handle a variety of snow conditions, making it versatile for different scenarios.

Similarly, the 932507 model, featuring a powerful 520cc engine, provides significant clearing capabilities. Users will appreciate the 24-inch clearing width and the ability to throw snow up to 50 feet. The unique design includes oversized tires that enhance traction and maneuverability, ensuring users can confidently navigate through driveways and pathways even in deep snow.

The Ariens 932039 model, powered by the 624cc engine, takes snow removal a step further. This powerful machine's 26-inch clearing width allows for faster snow processing, and its auto-turn steering technology provides effortless handling around obstacles, a critical feature for those with tight driveways or pathways.

With the 932505 model, users can utilize the 724cc engine, making it one of the more powerful options in this lineup. Its 28-inch clearing width couples with an advanced impeller system that maximizes snow throwing distance, making it perfect for large areas. Additionally, the heated handgrips improve comfort during prolonged use in frigid conditions.

Finally, the Ariens 932508, equipped with a 624cc engine, combines strength with ease of use. Its user-friendly control panel and electric start feature provide convenience, making it ideal even for those less experienced with snow blowers. The combination of a 26-inch clearing width ensures efficient snow removal, while the durable construction promises longevity.

Each of these Ariens models comes with a host of features designed for efficiency. From adjustable speed settings to high-impact and rust-resistant materials, these machines are built to withstand the rigors of winter. Whether facing light snow or heavy drifts, the Ariens 932038, 932507, 932039, 932505, and 932508 snow blowers deliver the reliability and performance users expect, ensuring that winter does not hinder outdoor activities.