Ariens 932508 - 624 manual Traction Drive Belt Replacement, Attachment CLUTCH/BRAKE Adjustment

Page 23

TRACTION DRIVE BELT

REPLACEMENT

NOTE: Housing and frame must be tipped apart and attachment drive belt removed from engine sheave in order to change traction drive belt (Figures 18 and 19).

CAUTION: Always support Sno- Thro frame and blower housing when loosening the cap screws holding them together. Never loosen cap screws while unit is in service position.

1.Remove attachment drive belt (See Remove Attachment Drive Belt).

2.Pull idler away from traction drive belt and remove belt from idler, camshaft pulley and driven pulley (it may be necessary to turn camshaft pulley using recoil starter handle).

NOTE: To gain clearance, engage traction clutch and if necessary pull back attachment idler arm.

3.Replace traction drive belt making sure pulleys align. If alignment is necessary, loosen camshaft pulley set screws, reposition pulley and retighten set screws.

4.Replace attachment drive belt (See Replace Attachment Drive Belt).

ATTACHMENT CLUTCH/BRAKE ADJUSTMENT

WARNING: IMPROPER ADJUSTMENT could result in unexpected movement of auger and impeller causing death or serious injury. AUGER / IMPELLER MUST STOP within 3 seconds when Attachment Clutch/Impeller Brake Bail is released.

WARNING: Adjustment procedure requires the engine to be run with the belt cover off. AVOID INJURY. Read and understand the entire Safety section before proceeding.

1.Remove belt cover.

2.Check belt alignment (Figure 19).

Engine sheave and attachment pulley must align vertically. Also, belt must be centered in the idler pulley.

To align, move engine sheave: a.Loosen set screws.

b.Slide sheave and key to desired position.

c.Tighten set screws. 3. Adjust cable slack.

IMPORTANT: The clutch cable must be slack when clutch bail is disengaged.

a.Center the upper cable adjuster on the mounting bracket, if necessary (Figure 20).

Upper Cable

 

Adjuster

 

Figure 20

OS2460

b.With the clutch bail disengaged, loosen the control cable mounting nuts on the attachment clutch arm (Figure 23).

c.Pull up on the cable body to remove cable slack.

d.Finger tighten mounting nuts and then loosen the top nut five turns.

e. Tighten the bottom nut with a wrench.

4.Check attachment clutch bail measurement.

a.Start engine and run at full throttle.

b.Slowly squeeze the attachment clutch bail until auger shaft begins to rotate.

c.Measure the distance from the end of the clutch bail to the handlebar as shown in Figure 22. The distance between the clutch bail and the handlebar should be 3-1/2 ± 1/8 in. (8.9 cm ± 3 mm).

d.Shut off engine.

5.Adjust attachment clutch bail measurement, if necessary.

a.Loosen idler nut (Figure 19).

b.To increase distance between clutch bail and handlebar, move the idler towards the attachment belt.

GB - 23

Image 23
Contents Sno-Thro Handgeführte Schneefräse Spazzaneve Semovente ’opérateur Vibrationswerte An den Händen Introduction Table of ContentsSafety Required Operator Training Safety Decals LocationsDo not allow adults to operate unit without proper training Safety RulesPage Unfold Handlebar Figure AssemblyAssembly Tools Required932507 932037, 039, 505 Check Engine Crankcase Oil Discharge ChuteCheck Tire Pressure Check Auger Gearcase OilControls and Features Operation Controls and FeaturesRecoil Starter Handle Snow Clean-Out ToolThrottle Electric StarterPRE-START Filling Fuel TankStarting and Shut OFF To Stop in AN EmergencySnow Removal MaintenanceService Position TravelingMaintenance Schedule Discharge Chute Service and AdjustmentsGeneral Lubrication Discharge Chute DeflectorScraper Blade Speed Selector AdjustmentFor Replacement RunnersRemove Attachment Drive Belt Attachment Drive Belt ReplacementImportant Belt Finger Must be Replace Attachment Drive BeltAttachment CLUTCH/BRAKE Adjustment Traction Drive Belt ReplacementTraction Drive Clutch Adjustment Remove Friction Disc Friction Disc ReplacementLong Term Reinstall Friction DiscStorage Short TermTroubleshooting Service PartsAccessories Reverse Does notOperate ForwardSize and Weight SpecificationsYear Limited Sno-Thro Warranty
Related manuals
Manual 31 pages 47.91 Kb

932508 - 624, 932505 - 724, 932507 - 520, 932039 - 624, 932037 - 724 specifications

Ariens has long been celebrated for its commitment to quality and durability in outdoor power equipment, and the Ariens 932038, 932507, 932039, 932505, and 932508 models are a testament to that legacy. These snow blowers offer a blend of robust performance, advanced technology, and user-friendly features that make them essential for managing winter weather.

The Ariens 932038 model stands out with its 5520 engine, delivering dependable power designed to tackle heavy snowfalls. Its 24-inch clearing width ensures efficient snow removal, while the high-quality, heavy-duty construction guarantees long-lasting performance. Equipped with an adjustable auger, the 932038 can handle a variety of snow conditions, making it versatile for different scenarios.

Similarly, the 932507 model, featuring a powerful 520cc engine, provides significant clearing capabilities. Users will appreciate the 24-inch clearing width and the ability to throw snow up to 50 feet. The unique design includes oversized tires that enhance traction and maneuverability, ensuring users can confidently navigate through driveways and pathways even in deep snow.

The Ariens 932039 model, powered by the 624cc engine, takes snow removal a step further. This powerful machine's 26-inch clearing width allows for faster snow processing, and its auto-turn steering technology provides effortless handling around obstacles, a critical feature for those with tight driveways or pathways.

With the 932505 model, users can utilize the 724cc engine, making it one of the more powerful options in this lineup. Its 28-inch clearing width couples with an advanced impeller system that maximizes snow throwing distance, making it perfect for large areas. Additionally, the heated handgrips improve comfort during prolonged use in frigid conditions.

Finally, the Ariens 932508, equipped with a 624cc engine, combines strength with ease of use. Its user-friendly control panel and electric start feature provide convenience, making it ideal even for those less experienced with snow blowers. The combination of a 26-inch clearing width ensures efficient snow removal, while the durable construction promises longevity.

Each of these Ariens models comes with a host of features designed for efficiency. From adjustable speed settings to high-impact and rust-resistant materials, these machines are built to withstand the rigors of winter. Whether facing light snow or heavy drifts, the Ariens 932038, 932507, 932039, 932505, and 932508 snow blowers deliver the reliability and performance users expect, ensuring that winter does not hinder outdoor activities.