Ariens 932507 - 520, 932037 - 724 Attachment Drive Belt Replacement, Remove Attachment Drive Belt

Page 21

2.Pull shift rod and adjustment pivot pin out of speed selector lever.

3.Place the speed selector lever in the fastest forward speed position.

4.Pull the shift rod straight down towards the ground as far as it will go.

5.Thread the adjustment pivot pin along the shift rod until it aligns with the mating hole on the speed selector lever.

6.Reinsert the pivot pin into the hole on the speed selector lever.

7.Check forward and reverse speeds.

a.Start unit.

b.Shift speed selector into first forward speed.

c.Engage traction clutch. Unit should move forward.

d.Stop unit.

e.Shift speed selector into first reverse speed.

f.Engage traction clutch. Unit should move backward.

g.Shut off unit.

8.Adjust pivot pin as needed so unit travels forward when speed selector lever is in first forward position and backward when speed selector lever is in first reverse position.

9.Secure adjustment pivot pin to speed selector lever with hairpin.

3

4

2

1

OSs0195

1.Shift Rod

2.Adjustment Pivot Pin

3.Speed Selector Lever

4.Hair Pin

Figure 17

ATTACHMENT DRIVE BELT REPLACEMENT

Remove Attachment Drive Belt

(Figures 18 and 19)

1.Shut off engine, remove key, disconnect spark plug wire and allow unit to cool completely.

2.Remove two screws securing belt cover to unit and remove belt cover.

3.Remove spring pin from chute crank rod assembly and separate (932037, 039, 505, 507, 508).

4.Remove hardware holding chute strap to engine and lift discharge chute off housing.

5.Remove belt finger by removing cap screw mounting belt finger to engine (Figure 19).

6.Remove attachment drive belt from engine sheave (it may be necessary to turn engine sheave using recoil starter handle).

CAUTION: Always support Sno-Thro frame and housing when loosening the cap screws holding them together. Never loosen cap screws while unit is in service position.

IMPORTANT: To avoid bending bottom cover, when tipping unit apart, support handlebars firmly or tip unit up on housing and remove bottom cover by removing four cap screws before separating unit.

7.Support Sno-Thro frame and housing.

8.Remove top two cap screws and loosen lower cap screws holding blower housing to frame (one on each side).

9.Separate housing from unit. Lower handlebar on floor.

10.Remove attachment drive belt from lower pulley (hold brake away from belt).

GB - 21

Image 21
Contents Sno-Thro Handgeführte Schneefräse Spazzaneve Semovente ’opérateur Vibrationswerte An den Händen Introduction Table of ContentsSafety Required Operator Training Safety Decals LocationsDo not allow adults to operate unit without proper training Safety RulesPage Assembly AssemblyTools Required Unfold Handlebar Figure932507 932037, 039, 505 Check Tire Pressure Discharge ChuteCheck Auger Gearcase Oil Check Engine Crankcase OilControls and Features Operation Controls and FeaturesThrottle Snow Clean-Out ToolElectric Starter Recoil Starter HandlePRE-START Filling Fuel TankStarting and Shut OFF To Stop in AN EmergencyService Position MaintenanceTraveling Snow RemovalMaintenance Schedule General Lubrication Service and AdjustmentsDischarge Chute Deflector Discharge ChuteFor Replacement Speed Selector AdjustmentRunners Scraper BladeRemove Attachment Drive Belt Attachment Drive Belt ReplacementImportant Belt Finger Must be Replace Attachment Drive BeltAttachment CLUTCH/BRAKE Adjustment Traction Drive Belt ReplacementTraction Drive Clutch Adjustment Remove Friction Disc Friction Disc ReplacementStorage Reinstall Friction DiscShort Term Long TermService Parts AccessoriesTroubleshooting Operate Does notForward ReverseSize and Weight SpecificationsYear Limited Sno-Thro Warranty
Related manuals
Manual 31 pages 47.91 Kb

932508 - 624, 932505 - 724, 932507 - 520, 932039 - 624, 932037 - 724 specifications

Ariens has long been celebrated for its commitment to quality and durability in outdoor power equipment, and the Ariens 932038, 932507, 932039, 932505, and 932508 models are a testament to that legacy. These snow blowers offer a blend of robust performance, advanced technology, and user-friendly features that make them essential for managing winter weather.

The Ariens 932038 model stands out with its 5520 engine, delivering dependable power designed to tackle heavy snowfalls. Its 24-inch clearing width ensures efficient snow removal, while the high-quality, heavy-duty construction guarantees long-lasting performance. Equipped with an adjustable auger, the 932038 can handle a variety of snow conditions, making it versatile for different scenarios.

Similarly, the 932507 model, featuring a powerful 520cc engine, provides significant clearing capabilities. Users will appreciate the 24-inch clearing width and the ability to throw snow up to 50 feet. The unique design includes oversized tires that enhance traction and maneuverability, ensuring users can confidently navigate through driveways and pathways even in deep snow.

The Ariens 932039 model, powered by the 624cc engine, takes snow removal a step further. This powerful machine's 26-inch clearing width allows for faster snow processing, and its auto-turn steering technology provides effortless handling around obstacles, a critical feature for those with tight driveways or pathways.

With the 932505 model, users can utilize the 724cc engine, making it one of the more powerful options in this lineup. Its 28-inch clearing width couples with an advanced impeller system that maximizes snow throwing distance, making it perfect for large areas. Additionally, the heated handgrips improve comfort during prolonged use in frigid conditions.

Finally, the Ariens 932508, equipped with a 624cc engine, combines strength with ease of use. Its user-friendly control panel and electric start feature provide convenience, making it ideal even for those less experienced with snow blowers. The combination of a 26-inch clearing width ensures efficient snow removal, while the durable construction promises longevity.

Each of these Ariens models comes with a host of features designed for efficiency. From adjustable speed settings to high-impact and rust-resistant materials, these machines are built to withstand the rigors of winter. Whether facing light snow or heavy drifts, the Ariens 932038, 932507, 932039, 932505, and 932508 snow blowers deliver the reliability and performance users expect, ensuring that winter does not hinder outdoor activities.