Swim'n Play 420745-15 warranty Liner Installation, Correct, Incorrect

Page 19

LINER INSTALLATION

19

LINER

CAUTION

YOUR POOL IS DESIGNED TO PROVIDE AN AMPLE SAFETY MARGIN WHEN IT STANDS ON LEVEL GROUND. FOR THIS PURPOSE A SLOPE IN EXCESS OF 2 INCHES IN ANY DIRECTION WALL TO WALL IS CONSIDERED OFF LEVEL YOUR POOL WARRANTY ONLY APPLIES TO POOLS INSTALLED ON LEVEL GROUND AS DEFINED ABOVE.

ONCE YOU HAVE STARTED TO FILL THE POOL, DO NOT TRY TO PULL THE LINER FORCEFULLY. THE WEIGHT OF EVEN ONE INCH OF WATER WILL MAKE IT IMPOSSIBLE TO MOVE THE LINER WITHOUT DAMAGING IT.

CORRECT

 

POOL

POOL

WALL

LINER

 

 

EARTH

 

MOUND

INCORRECT

AIR POOL

SPACE LINER

TOP RAIL

PLASTIC EDGING

STANDARD OVERHANG LINER

VINYL LINER

1.Clear all sticks and sharp objects from an area near the pool, that is as large as the pool itself. Remove the liner from its carton and unfold and open the liner. Refold the liner so that it can easily be carried to the pool and unfold from the outside of the pool. Check the levelness of the sand in the pool and make sure that no sharp objects are still in the pool.

2.Place the liner into the pool while holding onto the top of the wall section of the liner. Overhang the top wall of the liner over the pool wall approximately 4” and hold it by temporarily placing the plastic edging over the liner and the wall. Continue in this manner around the entire pool.

OUTSIDE VIEW OF POOL WALL

3.Gently pull on the liner and use a soft bristle broom to remove as many wrinkles as possible on the bottom of the pool. Adjust the overhang of the liner as needed as you go trying to keep it as equal as possible around the pool.

4.Be sure that the seam of the liner where the wall meets the floor of the liner is evenly centered in the pool. Start filling the pool slowly with water. Continue pulling gently and working the liner with a broom, and readjusting the overhang as necessary.

5.Some wrinkling of the liner may be evident and in no way affects the structural strength of your pool.

Once the water is filled to a point that the liner is pressed firmly against the wall install the thru-the-wall skimmer following its instructions. Then you can fill the entire pool as quickly as desired. The excess liner material overhanging the wall can either be trimmed later when the pool is filled, or double folded now to the inside of the pool between the liner and the wall. Permanently install the plastic edging around the entire pool, not leaving any gaps.

19

Image 19
Contents Oval Pool Contract Installations Some Friends To Help OUT IntroductionInstallation Assembly Steps Fig. D Deluxe Pools Supreme PoolsPreparing the Ground Actual Pool Dimensions Clearance SizeNail Clearance Radius Center Stake CARPENTER’S Level Leveling the GroundSide Support Assembling Important All trenches must be 3 feet apart from its center Prepare Buttress TrenchesPlates & Vertical Plates Assembly END Support Post AssemblyCenter Support Post Assembly Filling Trenches & Bottom Supports Level Support AssemblyAssembling Bottom Straps Hold Down Plates Sizes Strap Assembly for Slim Style Oval PoolsInsert Wall Into Bottom Rails Bottom Rail and Strap LayoutExample of Basic Layout Serrated Flange NUT Closing the WallPool Wall Protect Your LinerRechecking Your Work Filling the TrenchesTHRU-THE-WALL Skimmer OnlyEarth Mound Earth MoundIncorrect Liner InstallationLiner CorrectCove EZ Hook Liner InstallationVERTICALS, TOP Plates and Rails PRE-ASSEMBLY of TOP PlatesVertical Over Support Post Rail Placement of Warning Labels Installing Ledges7 Deluxe TOP Covers Installing TOP CoversTOP Cover Ledge Inside Cover 9 TWO-PIECE Wrap around Cover PedestalLogo TOP Cover WrapOutside Cover Pool User Warning Labels Safety Brochures and Education ProgramsSafety Tips Rules and Regulations Care of Pool Water Preventative Maintenance TipsLife Saving Equipment Winter CareANY Objects That MAY Provide Access to the Pool