ViewSonic PJD6653WS, PJD6553W, PJD6683W, PJD6383 Important safety instructions, Safety Instructions

Page 7

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1.Please read this manual before you operate your projector. Save it for future reference.

2.Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3.Refer servicing to qualified service personnel.

4.Always open the lens shutter or remove the lens cap when the projector lamp is on.

5.In some countries, the line voltage is NOT stable. This projector is designed to operate

safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate

or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

6.Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press BLANK on the projector or remote control.

7.The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

8.Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

9.Never replace the lamp assembly or any electronic components unless the projector is unplugged.

10.Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

11.Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

12.Do not place this projector in any of the following environments.

-Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

-Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

-Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the projector's life span and darkening the picture.

-Locations near fire alarms

-Locations with an ambient temperature above 40°C / 104°F

-Locations where the altitudes are higher than 3000 m (10000 feet).

2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents User Guide Compliance Information Important Safety Instructions Declaration of RoHS Compliance Copyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Projector Controls and functionsRemote control Operating the Laser pointer Remote control codeRemote control effective range Using the remote mouse controlSet the input signal to D-Sub / Comp , D-Sub / Comp or Hdmi Replacing the remote control batteries Choosing a location Positioning your projectorPJD5126/PJD5226 /PJD6223 Projection dimensionsPJD6353/PJD6353s/PJD6383/PJD6383s PJD6253PJD5226w PJD5226w/PJD6553w/PJD6653w/PJD6653wsPJD6653w/PJD6653ws/PJD6683w/PJD6683ws PJD6553wPJD6683ws PJD5126/PJD5226 PJD5226w ConnectionTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorBetter video quality Connecting Video source devicesConnecting audio Best video qualityTo connect the projector to a Component Video source device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to an Hdmi deviceTo connect the projector to a composite Video source device Connecting an S-Video source deviceConnecting a composite Video source device To connect the projector to an S-Video source deviceStarting up the projector OperationSystem Setup Advanced Using the menusUse / to highlight the System Setup Basic menu System Setup BasicSetting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signalFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsSelecting the aspect ratio About the aspect ratio Optimizing the image Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp /2 analog RGBGo to the Picture Color Mode menu Using Screen ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Tint Adjusting BrightnessAdjusting Contrast Adjusting ColorTo adjust the settings About color temperaturesColor Management To cancel the timer, perform the following steps Setting the presentation timerOperating in a high altitude environment Hiding the imageLocking control keys Freezing the imageCreating your own startup screen If you are in a Dhcp environment Configuring the LAN Control SettingsTo highlight LAN Control Settings and press MODE/ENTER on Controlling the projector through a LAN environmentIf you are in a non-DHCP environment Controlling the projector through a web browserCategory Item Input Length Maximum Number Characters You can press To reveal More buttons About Crestron e-ControlIP ID Crestron RoomView Enabled User Password New Password Confirm Admin PasswordPJLink, SNMP, AMX and Xpanel formats supported Using the projector in standby modePower Saving Shutting down the projectorMenu system Menu operationBasic SourceDhcp AdvancedInformation Description of each menu Reference Color ModeTemperature SettingsColor Space TimerQuick Auto SearchProjector Auto PowerBlank Timer LanguageCaption AudioMenu ClosedControl Code Reset AllSecurity RemoteCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampType number RLC-071 Replacing the lampType number RLC-077 Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Lamp events IndicatorsPower events Light Status & DescriptionCause Remedy TroubleshootingProjector specifications SpecificationsRequirements Input terminalPJD5126/PJD5226/PJD5226w Ceiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputCopyright Copyright informationDisclaimer IR control table AppendixCode a Code B Pin assignment for this two end RS232 command tableRS232/RJ45 command table RJ45 response tableReset Execute Front Table Horizontal Brightest Gain Write Reset Lamp Customer Support Limited Warranty Effect of state law Sales outside the U.S.A. and Canada Mexico Limited Warranty Número Gratis DE Asistencia Técnica Para Todo México
Related manuals
Manual 2 pages 56.35 Kb

PJD5226, PJD6353, PJD6383S, PJD6683WS, PJD6223 specifications

The ViewSonic PJD6553W is a high-performance DLP projector designed to meet the needs of both educational environments and business presentations. With a resolution of 1280 x 800, this projector provides a widescreen aspect ratio of 16:10, making it suitable for displaying a variety of content, from PowerPoint presentations to HD videos.

One of the standout features of the PJD6553W is its brightness level, boasting 3,200 lumens. This high brightness ensures that images remain clear and vibrant even in well-lit rooms, allowing for flexible usage in various settings without the need for dimming lights.

The PJD6553W employs DLP technology, which is known for its reliability and consistent image quality. This technology helps in delivering sharp and crisp details, vital for conveying information effectively. Additionally, the projector features a high contrast ratio of 15,000:1, which enhances the depth and richness of colors, ensuring that presentations are not only informative but visually engaging.

Another significant aspect of the ViewSonic PJD6553W is its long lamp life, which can last up to 6,000 hours in Eco mode. This reduces the frequency of replacements, lowering maintenance costs and ensuring that users can focus on their presentations rather than on projector upkeep.

Connectivity options are extensive with the PJD6553W, including HDMI, VGA, and composite inputs, allowing for seamless integration with various devices such as laptops, tablets, and media players. The inclusion of an integrated speaker enhances the overall experience, providing audible support for presentations without the need for external speakers.

For added convenience, the PJD6553W also features a 1.1x optical zoom, which provides flexibility in projector placement and allows for adjustments without needing to physically move the projector. Its compact design and lightweight nature make it portable, suitable for both fixed installations and on-the-go presentations.

In summary, the ViewSonic PJD6553W is a versatile and powerful projector that combines advanced technology with user-friendly features. Its high brightness, excellent connectivity options, long lamp life, and superior image quality make it an ideal choice for educators and business professionals seeking impactful visual presentations.
Top Page Image Contents