ViewSonic PJ452 manual Important Safety Instructions

Page 3

Important Safety Instructions

1.Read these instructions completely before using the equipment.

2.Keep these instructions in a safe place.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this equipment near water.

6.Clean with a soft, dry cloth.

7.Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.

9.Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the plug does not fit into your outlet, consult an electrician for replacement of the outlet.

10.Protect the power cord from being tread upon or pinched particularly at the plug, and the point where if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily accessible.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the equipment. When a cart is used, use caution when moving the cart/equipment combination to avoid injury from tipping-over

13.Unplug this equipment when it will be unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

ViewSonic PJ452

ii

Image 3
Contents PJ452 LCD Projector Compliance Information Important Safety Instructions Copyright Information PJ452 Model No.VS10948 About this manualTrademark acknowledgment Contents About contents of package Projector featuresProjector Part namesRemote control ControlsMagnify Fastening the lens cover PreparationsPutting batteries Using the remote control About the filter cover for bottom-up use Setting up At 43 screen ArrangementAdjusting the projectors elevator About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting power supply Turning on the power Power on/offTurning off the power Temporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom magnifying power Adjusting the focusCorrecting the keystone distortions Using the automatic adjustment featureAt a video signal Adjusting the positionUsing the partial magnify feature Freezing the screenTemporarily blanking the screen To choose the target menu Multifunctional settingUsing the menu function To display a menuTo choose the target item To return to the previous menu Setup MenuTo reset To operateMode AspectZoom KeystoneFilter Time ResetWhisper MirrorTo adjust #1 CUSTOM, #2 Custom or #3 Custom Using a test patternPicture menu High Middle Custom LOW To adjust CustomLOAD1 LOAD2 LOAD3 LOAD4 ProgressiveTV Film Turn OFF MY MemoryOver Scan PhaseImage menu NormalExecute Auto AdjustAt a video signal SizeFormat Auto Ntsc PAL Secam Input menuSpace Auto RGB VideoFrame Lock Turn on Turn OFFInformation Normal Hinvert Vinvert H&VINVERT Setup menuVolume Normal WhisperScreen menu Start UP Message No Input is DetectedSync is OUT of Range Auto OFF Option menuSearch RGB S-VIDEO VideoLamp Time Reset  CancelHigh Normal ServiceFAN Speed Auto Adjust Factory Reset Ghost Enable DisableLamp MaintenanceCase of replacement by yourself Air filter ViewSonic PJ452 Inside of the projector Other careRelated messages TroubleshootingInternal portion temperature is rising Regarding the indicator lamps Has become heated It is time to clean the air filter, or there is no airCooling fan is not operating There is a possibility that the interior portionElectrical power cord is not plugged Power switch is not set to the on positionPhenomena that may easily be mistaken for machine defects Color Space setting is not suitable Signal cables are not correctly connectedBrightness is adjusted to an extremely Color settings are not correctly adjusted 25, 28Specifications Warranty and after-serviceSpecifications Unit mm Customer Support Limited Warranty ViewSonic Projector