Eiki lc-sb15 owner manual Basic Operation, Turning On the Projector, Turning Off the Projector

Page 19

Basic Operation

Turning On the Projector

1Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector.

26

2Connect the projector's AC power cord into an AC outlet. The POWER indicator flashes red in a moment and turns on red.

3Press the POWER ON-OFF button on the top control or on the remote control. The POWER indicator turns green, and the cooling fans start to operate. The preparation display appears on

	the screen and the count down starts.	The preparation display disappears after 30 seconds.
4	After the count-down, the input source that was selected last		Selected Input Source
	appears on the screen.		Selected Input Source

Turning Off the Projector

1Press the POWER ON-OFF button on the top control or on the remote control, and a message "Power off?" appears on the screen.

2Press the POWER ON-OFF button again to turn off the projector. The POWER indicator starts to flash red, and it continues while the cooling fans are operating (for about 90 seconds).

3When the projector has cooled down enough to be turned on again, the POWER indicator lights red. Then you can disconnect the AC power cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

DO NOT DISCONNECT AC POWER CORD WHILE COOLING FANS ARE RUNNING OR BEFORE POWER INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT IN SHORTENING LAMP LIFE.

The message disappears after 4 seconds.

NOTE

●The projector cannot be turned on during the cooling period with the POWER indicator flashing red. You can turn it on again after the POWER indicator lights red.

●When the On start function is on, this projector is turned on automatically by connecting the AC power cord to an AC outlet. (See page 39 for the On start function.)

●Do not use the projector for more than 24 hours continuously. Turn off the projector at least once in 24 hours and give it a rest. Continuous use may result in shortening the lamp lifetime.

●This projector monitors internal temperature and automatically controls the running speed of the cooling fans.

●If the WARNING indicator flashes or lights red, see “Warning Indicator” on page 41.

19

Image 19

Contents Model LC-SB15 Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsMoving the Projector Safety InstructionsInstalling the Projector in Proper Position Air CirculationFederal Communication Commission Notice Compliance200 240 V AC ComplianceFor Continental Europe For the U.S.A. and CanadaFeatures and Design Bottom Part Names and FunctionsFront BackTerminal Part Names and FunctionsUi o TopSignal Emission indicator Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangeAdjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationTerminals Connecting to Video EquipmentProjector Turning On the Projector Basic OperationTurning Off the Projector Basic Operation Zoom AdjustmentFocus Adjustment Keystone AdjustmentDirect Operation Timer FunctionSound Adjustment No Show FunctionOn-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Input Source Selection Computer InputRGB Mode Computer InputComputer System Selection AutoAuto PC Adj Computer Adjustment AutoPC Adjust Menu To store adjustment dataComputer Adjustment Manual To clear adjustment data ResetMode free Display area To store adjustment dataImage Level Selection Image Level Adjustment Screen Size Adjustment Source Select Menu Video Video InputInput Source Selection Video, S-Video Input button Video Computer Video button VideoRGB Scart Video InputInput Source Selection Component, RGB Scart 21-Pin ComponentAV System Menu Video or S-Video Video System SelectionVideo or S-Video AutoImage button Standard Cinema CinemaTint ColorProgressive Resets all adjustment to their previous figure Setting SettingSetting To change the code for the projector To change the code for the remote controlThen check the items below Maintenance and CleaningProjector is shut down and the Warning indicator lights red TOP ControlCleaning the Projector Cabinet Maintenance and CleaningCleaning the Air Filters Cleaning the Projection LensReset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingAppendix Projector is OFF. The AC power cord is unplugged Indicators and Projector ConditionInput PC AdjustImage Select Image Adjust Screen Menu TreeImage Adjust Screen Sound SettingImage Select KHz Compatible Computer SpecificationsResolution FreqTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Configurations of TerminalsTerminal HDB15-PIN Pin Configuration Terminal DVI-I Pin ConfigurationKA-DV20 Service Port ConnectorOptional Parts POA-MACAPAttaching the Lens Cover Page Key to better communications Canada