Eiki lc-sb15 owner manual Lamp Replace Counter, When the lamp replace counter is reset, the Lamp

Page 44

Maintenance and Cleaning

Lamp Replace Counter

Be sure to reset the lamp replace counter after the lamp is replaced. REPLACE indicator stops lighting.

1Turn the projector on, press the MENU button and the On- Screen Menu will appear. Press the Point Left/Right button

to move the red frame pointer to the Setting Menu icon.

2Press the Point Down button to move the red frame pointer to the Lamp counter reset item and then press the SELECT button. The message "Lamp replace counter Reset?" is displayed. Move the pointer to [Yes] and then press the SELECT button.

3Another confirmation dialog box appears and select [Yes] to reset the Lamp replace counter.

NOTE

●Do not reset the Lamp replace counter without implementation of lamp replacement. Be sure to reset the Lamp replace counter only after replacing the lamp.

When the lamp replace counter is reset, the LAMP

Move the pointer to Lamp counter reset and then press the SELECT button. The message “Lamp replace counter Reset?” is displayed.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

●Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

( Follow carefully the instructions in the Lamp Replacement section of this manual. ) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

●A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Model LC-SB15 Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandSafety Instructions Installing the Projector in Proper PositionAir Circulation Moving the ProjectorCompliance Federal Communication Commission NoticeCompliance For Continental EuropeFor the U.S.A. and Canada 200 240 V ACFeatures and Design Part Names and Functions FrontBack BottomPart Names and Functions TerminalTop Ui oRemote Control Signal Emission indicatorLaser Pointer Function Pointer FunctionRemote Control Code Wireless Mouse OperationRemote Control Operating Range Remote Control Batteries InstallationPositioning the Projector InstallationAdjustable Feet Installation Connecting to a ComputerProjector Connecting to Video EquipmentTerminals Turning Off the Projector Basic OperationTurning On the Projector Zoom Adjustment Focus AdjustmentKeystone Adjustment Basic OperationTimer Function Sound AdjustmentNo Show Function Direct OperationRemote Control On-Screen MenuTop Control On-Screen MenuMenu Bar RGB Computer InputInput Source Selection Computer Input Computer System SelectionAuto ModeComputer Adjustment Auto PC Adjust MenuTo store adjustment data Auto PC AdjComputer Adjustment Manual Reset Mode freeDisplay area To store adjustment data To clear adjustment dataImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoInput button Video Computer Video button Video Source Select Menu VideoVideo Input Input Source Selection Component, RGB Scart 21-PinComponent RGB ScartVideo System Selection Video or S-VideoAuto AV System Menu Video or S-VideoCinema Image button Standard CinemaProgressive ColorTint Resets all adjustment to their previous figure Setting SettingSetting To change the code for the remote control To change the code for the projectorMaintenance and Cleaning Projector is shut down and the Warning indicator lights redTOP Control Then check the items belowMaintenance and Cleaning Cleaning the Air FiltersCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixAppendix Indicators and Projector Condition Projector is OFF. The AC power cord is unpluggedPC Adjust Image Select Image Adjust ScreenMenu Tree InputImage Select Sound SettingImage Adjust Screen Compatible Computer Specifications ResolutionFreq KHzTechnical Specifications Configurations of Terminals Terminal HDB15-PIN Pin ConfigurationTerminal DVI-I Pin Configuration DVI-I Terminal DIGITAL/ANALOGService Port Connector Optional PartsPOA-MACAP KA-DV20Attaching the Lens Cover Page Key to better communications Canada
Top Page Image Contents