Eiki LC-SX6A, LC-X6A Remote Control Battery Installation, Remote Control Channel & Frequency

Page 17

Preparation

Remote Control CH

Radio Frequency

 

 

CH 1

2.472 GHz

 

 

CH 2

2.403 GHz

 

 

CH 3

2.446 GHz

 

 

CH 4

2.421GHz

 

 

Channel switches sequentially for one pressing the SELECT button.

Remote Control ID

ID 1

ID 2

ID 3

ID 4

ID switches sequentially for one pressing the SELECT button.

Preparation

Table1: Remote Control Channel & Frequency

Default setting

ID 5

ID 6

ID 7

ID 8

Table2: Remote Control ID

Caution about Radio Wave

The remote control operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical equipment (such as pacemaker), as well as amateur radio stations.

Before operating the remote control, make sure no electromagnetic interference occurs and pay attention to the following cautions.

1.Be sure that there are no other devices in the area that may use the same frequency band as the remote control.

2.If any other devices are causing radio interferences, change the communication frequency channel or move to other location.

Caution in Wireless LAN Interference

Under wireless LAN environment based on IEEE 802.11b and IEEE802.11g, the remote control may not operate properly due to radio interferences. The remote control is initially set to use 2.472 GHz band (CH1) corresponding to several channels of wireless LAN.

Should the remote control not operate properly due to radio interference, switch the communication frequency channel to CH2. Yet the operating condition is not improved, try CH3 and CH4. In case of failure in every channel operation, relocate other radio equipment using 2.4 GHz band away from the remote control and the projector.

Remote Control Battery Installation

1

Open the battery

2

Install new batteries

3

Replace the compartment

compartment lid.

into the compartment.

lid.

 

 

 

Two

AA size alkaline

 

Press the lid downward

batteries

and slide it.

For correct polarity (+ and

 

 

–), be sure battery terminals

 

are in contact with pins in

 

the compartment.

To insure safe operation, please observe the following precautions: ● Use (2) AA or LR6 type alkaline batteries.

● Always replace the batteries in sets.

Do not use a new battery with a used battery.

Avoid contact with water or liquid.

Do not expose the remote control to moisture, or heat.

Do not drop the remote control.

If a battery has leaked on remote control, carefully wipe case clean and install new batteries.

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

17

Image 17
Contents LC-SX6A Compatibility My Menu Selection Features and DesignTable of Contents Risk of Electric Shock Do not Open To The OwnerVoor de klanten in Nederland Safety InstructionsPositioning Precautions Setup In Proper DirectionsAir Circulation Bottom Front Downward Upward UsualUSE Caution in Carrying or Transporting the Projector Moving the ProjectorFederal Communication Commission Notice ComplianceParts Name PreparationFront BackIndicators Top Control Input 2 terminals TerminalsC Jack USB Series BUSB Serial Port OUTAbout Control Pad Remote Control4REMOTE RESET/ON/ALL-OFF switch Timer buttonFreeze button CH buttonWired Remote Control Transmitter Remote Control TransmitterRemote Control Channel and ID Setup Remote Control ID Remote Control Battery InstallationRemote Control Channel & Frequency Installation InstallationLens Installation Positioning the ProjectorAdjustable feet Lens Shift AdjustmentLevel Adjustable Feet For Continental Europe Connecting AC Power CordFor the U.S.A. and Canada 200 240 V ACOption Control No Connection TerminalsInterface Board Slots Cables used for connection Connecting to Computer Digital and Analog RGBVideo Cable w S-Video Cable e DVI-D Cable Connecting to Video Equipment Digital and VideoBNC Cable Scart-VGA Cable e Component Cable Connecting to Video Equipment Component and RGB ScartBasic Operation Wireless Remote Control OperationOperating the Projector Mouse OperationPad Top Control Remote ControlBasic Operation and Reference Buttons Enter a PJ PIN code What is PIN code?Turning On the Projector Turning Off the Projector Remote Control Zoom and Focus AdjustmentShutter Function Top ControlInformation Auto PC AdjustmentInput Selection Timer Function Keystone AdjustmentScreen Selection Picture Freeze FunctionZoom Zoom +/- FunctionZoom + Remote Control Operation How to Operate On-Screen MenuTop Control Operation Mouse OperationControl bar for Mouse Operation Menu icon GuideMouse cursor Item dataMenu icons What You Can Do with Each Menu Menu Icons and Their FeaturesRGB Scart InputInput When video input signal is connected to When the input source is analog comingWhen the input source is component Move a pointer to Input 2 and press the Select buttonSystem SystemPC System Selection AutoComponent Signal Selection Video or S-Video Signal SelectionAV System Menu Video or S-Video AV System Menu ComponentPC Adjustment Computer AdjustmentAuto PC Adjust Auto PC adjManual PC Adjust Reset Sync phasePosition ModeImage Image AdjustmentFor PC Input For AV InputImage Adjust Color temp Auto picture controlRed GreenNoise reduction GammaProgressive FilmScreen Screen SettingScreen Setting Keystone ZoomCeiling RearSetting SettingLanguage MenuEnter a Logo PIN code LogoLamp BackgroundPower management Power managementDisplay Input searchShutter Analog outLens memory Security Shutter ManagementKey lock USB lockTo Change PJ PIN Code To Change the PJ PIN Code settingExits the Setting menu Factory defaultSpecial SpecialFan control FilterUSB memory Test patternRS-232C Information Exits Warning log menuThen check the matters below Maintenance and CleaningAll indicators except the Lamp indicator are blinking Filter cover Air filter Air Filter ReplacementLamp Lamp ReplacementReset the Lamp time Lamp Handling Precautions Attaching the Cord Cover Strap Cleaning the Projection LensCleaning the Projector Cabinet Main Indicators Indicators and Projector ConditionProjector is OFF. The AC power cord is unplugged May cause electric shock or a fire hazardAir filter is clogged with dust or has been used overtime Shutter IndicatorUntil cooling is completed Lamp Replace IndicatorsLamp 1/2 Appendix TroubleshootingLens position moves when Input Wireless Remote ControlIs switched Some displays are not seenFreq Compatible Computer Specifications1080i/50 1080i/60Technical Specifications Optional Parts AccessoriesScreen Screen Menu TreeImage Image ADJ Special Lamp Dimensions USB Connector Series B Terminal ConfigurationsLogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Numerics IndexAppendix Appendix Appendix Key to better communications Canada

LC-X6A, LC-SX6A specifications

The Eiki LC-SX6A and LC-X6A projectors are advanced devices designed for professional presentations and high-quality visual experiences. With a focus on outstanding image clarity and versatile performance, these projectors cater to a wide range of applications, from corporate meetings to educational environments.

Both models feature a powerful 6,000 ANSI lumens brightness, ensuring that presentations remain visible even in well-lit rooms. The high contrast ratio of 5,000:1 further enhances their capability by providing deeper blacks and more vibrant colors, enabling the audience to experience rich and dynamic visuals. The native resolutions are WUXGA (1920 x 1200) for the LC-SX6A and XGA (1024 x 768) for the LC-X6A, making them suitable for projecting detailed images and text.

One of the standout technologies incorporated in these projectors is the 3LCD system, which allows them to achieve exceptional color accuracy and uniform brightness. This means that users can expect true-to-life colors in their presentations, making the visuals more engaging and effective. Furthermore, Eiki’s Intelligent Color Management technology helps adjust color settings based on the content being projected, providing optimal viewing experiences tailored to specific applications.

Connectivity is another strong suit of the Eiki LC-SX6A and LC-X6A. They come equipped with multiple input options including HDMI, VGA, USB, and more, ensuring compatibility with a wide array of devices such as laptops, tablets, and media players. This versatility makes setup and operation seamless, reducing the time needed for technical preparations.

Both projectors feature a robust design aimed at durability, making them ideal for frequent use in various environments. Additionally, they include a lamp life of up to 6,000 hours in eco mode, which significantly lowers maintenance costs and extends the intervals between replacements.

To enhance user convenience, the projectors include features like a built-in camera for real-time monitoring and wireless options for remote presentations. They also come with a comprehensive suite of image optimization settings, allowing users to fine-tune projection quality according to their specific needs.

In summary, the Eiki LC-SX6A and LC-X6A projectors deliver a perfect blend of brightness, color fidelity, and connectivity that meets the demands of modern presentations in educational and professional settings. Their innovative technologies and robust characteristics make them a valuable investment for anyone seeking reliable and high-quality projection solutions.