Eiki LC-VC1 owner manual Turning on Projector, Turning OFF the Projector, Disconnect AC Power Cord

Page 20

TURNING ON PROJECTOR

1 Complete the peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to “CONNECTING TO PROJECTOR” on Pages 11~-13for connecting that equipment.)

2 Connect the projector’s AC Power Cord into an AC outlet and turn MAIN ON I OFF SWITCH to ON. LAMP Indicator lights RED, and READY Indicator lights GREEN.

NOTE : When “On start” function is ON, this projector is turned on automatically by switching MAIN ON / OFF SWITCH on. (Refer to page 37.)

3 Press POWER ON-OFF button on Top Control or on Remote Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and the count-down starts. The signal from the PC or Video source appears after 30 seconds.

TURNING OFF THE PROJECTOR

1. Press POWER ON-OFF button on Top Control or on Remote Control Unit, and the message “Power off?” appears on a screen.

2 Press POWER ON-OFF button again to turn off projector. LAMP Indicator lights bright and READY Indicator turns off. After projector is turned off, Cooling Fans operate (for 90 seconds). During this “Cooling Down” period, this appliance cannot be turned on.

3 When projector has cooled down, READY Indicator turns to green again and you can turn projector on. After cooling down completely, turn MAIN ON / OFF SWITCH to OFF and

disconnect AC Power Cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU

TURN PROJECTOR ON, WAIT AT LEAST 5

MINUTES BEFORE TURNING IT OFF.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on page 37.

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on

projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1.Turn MAIN ON / OFF SWITCH to OFF and disconnect the AC Power Cord from a AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See “AIR FILTER CARE AND CLEANING” section on page 38.)

4.Turn projector on again.

If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model LC-VC1 To the Owner Safety Instructions Compliances Table of Contents IBM-compatible and Macintosh computers up to Digital Zoom function magnifies the image up toPage Preparation Connecting AC Power Cord Positioning the Projector RecommendationAdjustable Feet Moving ProjectorPage Cables used for connection * = Cables are not Speaker Cable Mini Plug stereo Page TOP Control Remote Control Unit can be used as either Wired or Wireless Operating RangeWired Remote Control Operations HOW to Operate ON-SCREEN Menu Screen Menu Operation belowPress Menu button to display ON-SCREEN Menu Move Pointer red frame to Menu Icon that youMenu BAR Press Menu Button for PC input sourceDisconnect AC Power Cord Turning on ProjectorTurning OFF the Projector Projector againZoom Adjustment Focus AdjustmentLens Shift Adjustment Keystone AdjustmentPicture Freeze Function Mute SettingNo Show Function When projector cannot recognize connected signal as Direct OperationAuto PC Adjustment PC ADJ. button on Top Control or on Remote Control UnitMenu above. Refer to of Manual PC Adjustment section P26 Select Computer System ManuallyNumber of total dots in one horizontal period. Press Point Manual PC AdjustmentWhenever you use it To store adjustment parameters, move a red frame pointer to Compatible Computer Specifications Press Menu button and ON-SCREEN Menu will appear. Press Image Level Select DirectImage Level Select Menu Image Level Adjustment Better balance of contrast. From 0 toExpand function To compress the image size, press the D.ZOOM V button.Source through Menu Operation see below Video JACK, YIC Jacks or S-VIDEO Jack Projector automatically detects incoming Video systemImage Level Select Direct Video Mode Progressive cannot be selected when 480p, 575p or Set On to provide progressive scan modeColor. From 0 to Set On to reduce noise rough parts of the imageAspect ratio at wide video aspect ratio of 16 Provides image at the normal video aspect ratio of 4Power off? message On Screen MenuTo change the code of the Remote Control Press both Menu and Normal buttons on the Remote ControlAIR Filter Care and Cleaning Cleaning the Projection LensLamp Replacement Make sure that Lamp Assembly is set properly. Replace LampConnect AC Power Cord to projector and turn on projector Lamp Replace CounterPage Page Specifications are subject to change without notice Configurations of Terminals RGB TerminalEiki Czech SPOL. S.R.O
Top Page Image Contents