Eiki LC-VC1 owner manual To change the code of the Remote Control

Page 37

This function turns Projection Lamp off when projector detects signal interruption and projector is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when the input signal is interrupted and projector is not operated over 5 minutes. This function operates as follows;

1. When the signal is interrupted, “No signal” and the counting down display appears (for 5 minutes).

2. When Projection Lamp turned off, READY Indicator turns off. Cooling Fans operate and Projection Lamp is turned off for 90 seconds. (During this “Cooling Down” period, projector cannot be turned on.)

3. When Projection Lamp has cooled down, READY Indicator flashes and Projection Lamp can be turned on again (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when the input signal connected or projector is operated

with any button on the Top Control or on the Remote Control Unit.

.

When this function is “On,” projector is automatically turned on just by switching MAIN ON / OFF SWITCH on.

Note; Be sure to turn projector off properly (refer to the section “TURNING OFF THE PROJECTOR” on page 20.). If projector is turned off in the wrong steps, On Start function does not operate properly.

This projector has two different remote control codes; the factory-set normal code (Code 1) and the secondary code (Code 2). This switching function prevents the remote control operation mixture (jam) when operating several projectors or video equipment together. When operating projector in “Code 2,” both projector and Remote Control must be switched to “Code 2.”

To change the code of Projector:

Set the Remote control in the SETTING MENU to “Code 2.”

To change the code of the Remote Control:

Press both MENU and NORMAL buttons on the Remote Control

Unit together for over 10 seconds.

After changing the code, make sure the Remote Control operates properly.

To return to the normal code (Code 1), operate both projector and Remote Control in the ways above again.

NOTE: When batteries of the Remote Control Unit is replaced, the remote transmit code automatically returns to the normal code (Code 1).

This function is used to reset Lamp

Replace Counter. When replacing Projection Lamp, reset Lamp Replace

Counter by using this function. Refer to page 39 for operation

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Model LC-VC1 To the Owner Safety Instructions Compliances Table of Contents Digital Zoom function magnifies the image up to IBM-compatible and Macintosh computers up toPage Preparation Connecting AC Power Cord Recommendation Positioning the ProjectorMoving Projector Adjustable FeetPage Cables used for connection * = Cables are not Speaker Cable Mini Plug stereo Page TOP Control Operating Range Remote Control Unit can be used as either Wired or WirelessWired Remote Control Operations Screen Menu Operation below HOW to Operate ON-SCREEN MenuPress Menu button to display ON-SCREEN Menu Move Pointer red frame to Menu Icon that youPress Menu Button for PC input source Menu BARTurning on Projector Disconnect AC Power CordTurning OFF the Projector Projector againFocus Adjustment Zoom AdjustmentLens Shift Adjustment Keystone AdjustmentNo Show Function Mute SettingPicture Freeze Function Direct Operation When projector cannot recognize connected signal asPC ADJ. button on Top Control or on Remote Control Unit Auto PC AdjustmentMenu above. Refer to of Manual PC Adjustment section P26 Select Computer System ManuallyWhenever you use it Manual PC AdjustmentNumber of total dots in one horizontal period. Press Point To store adjustment parameters, move a red frame pointer to Compatible Computer Specifications Image Level Select Menu Image Level Select DirectPress Menu button and ON-SCREEN Menu will appear. Press Better balance of contrast. From 0 to Image Level AdjustmentTo compress the image size, press the D.ZOOM V button. Expand functionSource through Menu Operation see below Projector automatically detects incoming Video system Video JACK, YIC Jacks or S-VIDEO JackImage Level Select Direct Video Mode Set On to provide progressive scan mode Progressive cannot be selected when 480p, 575p orColor. From 0 to Set On to reduce noise rough parts of the imageProvides image at the normal video aspect ratio of 4 Aspect ratio at wide video aspect ratio of 16On Screen Menu Power off? messagePress both Menu and Normal buttons on the Remote Control To change the code of the Remote ControlCleaning the Projection Lens AIR Filter Care and CleaningMake sure that Lamp Assembly is set properly. Replace Lamp Lamp ReplacementConnect AC Power Cord to projector and turn on projector Lamp Replace CounterPage Page Specifications are subject to change without notice RGB Terminal Configurations of TerminalsEiki Czech SPOL. S.R.O
Top Page Image Contents