Intel AW-A795 user manual Installing Processors, User’s Manual

Page 11

2.2. Installing Processors

User’s Manual

CN4	Gigabit LAN Connector

CN5	Gigabit LAN Connector

CN6	Gigabit LAN Connector

CN7	Gigabit LAN Connector

CN8	Gigabit LAN Connector

CN9	Gigabit LAN Connector

CN10	COM1 RJ45 Connector

CN11	FAN Connector

CN12	Power LED Pin Header

CN13	USB1 Pin Header

CN14	COM2 Box Header

CN15	Parallel Box Header

CN16	ATX Power Connector

CN17	Mini PCI

CN18	GPIO Pin Header

CN19	SATA0 Connector

CN20	FAN Connector

CN21	SATA1 Connector

CN22	SATA LED Pin Header

CN23	HDD Power Connector

CN24	FAN Connector

CN25	IDE(2mm) 44 Pin 90 Degree

CN26	IDE(2.54mm) 40 Pin

CN27	+12V Power Connector

CN28	FAN Connector

CN29	FAN Connector

CN30	FAN Connector

CN31	FAN Connector

CN32	HDD LED Pin Header

CN33	PS-On Pin Header

CN34	Reset Pin Header

CN36	KB/MS Pin Header

CN37	LAN LED Pin Header

CN38	LAN LED Pin Header

Buzzer 1	Speak Buzzer

JP1	PS-On/Always On Select

JP2,4,5	PCI-X Slot Frequency Select

JP3	Speak Buzzer Enable

JP6	Clear CMOS

2.2. Installing Processors

The AW-A795 onboard built-in socket 479 for Intel® Pentium® 4 Processors. After installing the processor, you should proceed to installing the heatsink or cooler.

©2002 AEWIN Technologies Co., Ltd.. All rights reserved.

11

Ver 1.0. Jan. 2005

Image 11

Contents Control Board Model Number：AW-A795User’s Manual Intel Pentium 4 Embedded SBC with Six Gigabit/Two 10/100LAN SSDLimitation of Liability Copyright 2005. All Rights Reserved Manual Edition 1.0, JanuaryTrademarks Chapter 2. Connectors Location and Configuration Table of ContentsSpecification 1.5 Board Dimension3.2 Entering the CMOS Setup Program JP3Speak Buzzer EnableChapter 3. BIOS Setup 3.1 Quick Setup1.1Introduction Chapter 1. General InformationWatchdog Timer System Monitoring Digital I/O 1.2SpecificationCPU BIOS Chipset I/O Chipset Memory Enhanced IDE Serial port Parallel port KB/Mouse connector USB connectors PCI Slot1.3AW-A795 Package Precautions1.4 Board Layout 1.5 Board Dimension Chapter 2. Connectors/Switch Location and Configuration LAN 10/100 Connector LAN 10/100 Connector ConnectorDefine USB0 Connector2.2. Installing Processors 2.2.1 Installing CPU 3 Now you can take out the CPU from socket 2.2.2 Remove CPU 1 First, please push the tappet to unlock location1 Pentium M CPU Socket 2 PIII CPU - uFCPGA Package 2.2.3 How to recognize CPU3 Pentium 4 CPU Socket 2.3 Installing Memory To insert a DIMM Memory To Insert a DIMM Memory Please align the module with the socket key and press down until the levers at each end of the socket snap close up Ver 1.0. Jan CN2/3 LAN 10/100 Connector 2.4 Connector and Jumper SettingsCN1 USB0 Connector CN4/5/6/7/8/9Gigabit LAN connectorCN14 COM2 Box Header CN11/20/24/28/29/30/31FAN Connector CN12Power LED Pin HeaderPin Define CN13USB1 Pin Header Pin DefineDefine CN25IDE 2mm 44Pin 90 degree CN18 GPIO Pin HeaderCN26IDE2.54mm 40 Pin Connector JP1PS/On/Always On Select SettingFrequency JP2/4/5PCI-X Slot Frequency SelectJP6Clear CMOS JP3Speak Buzzer EnableChapter 3. BIOS Setup Enter the CMOS Setup program’s main menu as follows 3.2Entering the CMOS Setup ProgramPOWER MANAGEMENT SETUP STANDARD CMOS FEATURESADVANCED BIOS FEATURES ADVANCED CHIPSET FEATURESSAVE & EXIT SETUP LOAD FAIL-SAFE DEFAULTLOAD OPTIMIZED DEFAULTS SET SUPERVISORS & USER PASSWORDDescription Advanced BIOS Features SetupUse the Advanced BIOS Features Setup option as follows OptionVirus Warning Use the Advanced Chipset Features Setup option as follows Advanced Chipset Features Setupto this memory area, a system error may result Use the Integrated Peripherals Setup option as followsUse the Power Management Setup option as follows Power Management Use the PNP/PCI Configuration Setup option as follows Description Load Fail-Safe Defaults PC Health Status Configuration SetupLoad Optimized Defaults Supervisor/User Password Use this function to exit Setup without saving the CMOS value Save and Exit SetupExit Without Saving 4.1.1. Intel 82546EB Ethernet 1 Choose Ethernet Controller The system driver installation procedure must be performed firstChapter 4. Driver Utility 2 Choose Driver 3 Click Next 4 Click Next 5Click Next 6 Click Next 7 Click Finish 1. Insert the AW-A795 CD-ROM driver into the CD-ROM Drive 4.1.2 Intel 82551 Ethernet Installation2 . Select the Drivers/system file to click the Setup icon Please install Ethernet drivers as follows3 Click Next 4 Click Next 5 Click Next 6 Click Next 7 Click Finish 4.2.1 Install System Chipset Driver1 Click Next 2 Click Yes 3 Click Next 4 Click Finish Installation process is completed and allowed the system to rebootChannel Appendix A System Resource Interrupt ControllerAssignment Type Memory MapMemory below 1MB 1Mb ~ 640KB Address RangeUser’s Manual Terminating Appendix B Standard Cable ListCable Description AW-A795