Intel AW-A795 Appendix A System Resource Interrupt Controller, Assignment, Channel, User’s Manual

Page 51

User’s Manual

Appendix A :System Resource

Interrupt Controller

The AW-A795 is a fully PC compatible control board, it consists of 16 ISA interrupt request lines and most of them already in used by other part of the board. Please make sure that the IRQs do not conflict if you would like to use extra add-on cards.

System IRQs are available to cards installed in the ISA expansion Bus first. Any remaining IRQs then may be assigned to this PCI Bus. You are able to use the Microsoft’s Diagnostic(MSD.EXE) utility include in Windows director to see their map.

IRQ	Assignment
IRQ0	System Timer Output
IRQ1	Keyboard
IRQ2	Interrupt rerouting from IRQ8 through
	IRQ15
IRQ3	Serial Port 2
IRQ4	Serial Port 1
IRQ5	USB Controller
IRQ6	Floppy Disk Controller
IRQ7	Parallel Port 1
IRQ8	Real Time Clock
IRQ9	Ethernet Controller
IRQ10	Reserved
IRQ11	USB Controller
IRQ12	Mouse
IRQ13	Math Coprocessor
IRQ14	Primary IDE Controller
IRQ15	Secondary IDE Controller

DMA Channel Assignment：Channel 4 is by default used to cascade the two controllers

	Channel	Assignment
	DMA0	Available fir PCI and ISA Slot
	DMA1	Available for PCI And ISA Slot
	DMA2	Floppy Disk Controller
	DMA3	Available for PCI and ISA Slot
	DMA4	Cascade

©2002 AEWIN Technologies Co., Ltd.. All rights reserved.

50

Ver 1.0. Jan. 2005

Image 51

Contents Control Board Model Number：AW-A795User’s Manual Intel Pentium 4 Embedded SBC with Six Gigabit/Two 10/100LAN SSDCopyright 2005. All Rights Reserved Manual Edition 1.0, January TrademarksLimitation of Liability Chapter 2. Connectors Location and Configuration Table of ContentsSpecification 1.5 Board Dimension3.2 Entering the CMOS Setup Program JP3Speak Buzzer EnableChapter 3. BIOS Setup 3.1 Quick Setup1.1Introduction Chapter 1. General InformationWatchdog Timer System Monitoring Digital I/O 1.2SpecificationCPU BIOS Chipset I/O Chipset Memory Enhanced IDE Serial port Parallel port KB/Mouse connector USB connectors PCI Slot1.3AW-A795 Package Precautions1.4 Board Layout 1.5 Board Dimension Chapter 2. Connectors/Switch Location and Configuration LAN 10/100 Connector LAN 10/100 Connector ConnectorDefine USB0 Connector2.2. Installing Processors 2.2.1 Installing CPU 3 Now you can take out the CPU from socket 2.2.2 Remove CPU 1 First, please push the tappet to unlock location1 Pentium M CPU Socket 2 PIII CPU - uFCPGA Package 2.2.3 How to recognize CPU3 Pentium 4 CPU Socket 2.3 Installing Memory To insert a DIMM Memory To Insert a DIMM Memory Please align the module with the socket key and press down until the levers at each end of the socket snap close up Ver 1.0. Jan CN2/3 LAN 10/100 Connector 2.4 Connector and Jumper SettingsCN1 USB0 Connector CN4/5/6/7/8/9Gigabit LAN connectorCN14 COM2 Box Header CN11/20/24/28/29/30/31FAN Connector CN12Power LED Pin HeaderPin Define CN13USB1 Pin Header Pin DefineDefine CN25IDE 2mm 44Pin 90 degree CN18 GPIO Pin HeaderCN26IDE2.54mm 40 Pin Connector JP1PS/On/Always On Select SettingFrequency JP2/4/5PCI-X Slot Frequency SelectJP6Clear CMOS JP3Speak Buzzer EnableChapter 3. BIOS Setup Enter the CMOS Setup program’s main menu as follows 3.2Entering the CMOS Setup ProgramPOWER MANAGEMENT SETUP STANDARD CMOS FEATURESADVANCED BIOS FEATURES ADVANCED CHIPSET FEATURESSAVE & EXIT SETUP LOAD FAIL-SAFE DEFAULTLOAD OPTIMIZED DEFAULTS SET SUPERVISORS & USER PASSWORDDescription Advanced BIOS Features SetupUse the Advanced BIOS Features Setup option as follows OptionVirus Warning Use the Advanced Chipset Features Setup option as follows Advanced Chipset Features Setupto this memory area, a system error may result Use the Integrated Peripherals Setup option as followsUse the Power Management Setup option as follows Power Management Use the PNP/PCI Configuration Setup option as follows User’s Manual Load Fail-Safe Defaults PC Health Status Configuration SetupLoad Optimized Defaults Supervisor/User Password Save and Exit Setup Exit Without SavingUse this function to exit Setup without saving the CMOS value The system driver installation procedure must be performed first Chapter 4. Driver Utility4.1.1. Intel 82546EB Ethernet 1 Choose Ethernet Controller 2 Choose Driver 3 Click Next 4 Click Next 5Click Next 6 Click Next 7 Click Finish 1. Insert the AW-A795 CD-ROM driver into the CD-ROM Drive 4.1.2 Intel 82551 Ethernet Installation2 . Select the Drivers/system file to click the Setup icon Please install Ethernet drivers as follows3 Click Next 4 Click Next 5 Click Next 6 Click Next 7 Click Finish 4.2.1 Install System Chipset Driver1 Click Next 2 Click Yes 3 Click Next 4 Click Finish Installation process is completed and allowed the system to rebootAppendix A System Resource Interrupt Controller AssignmentChannel Type Memory MapMemory below 1MB 1Mb ~ 640KB Address RangeUser’s Manual Terminating Appendix B Standard Cable ListCable Description AW-A795