Intel S845WD1-E manual Peripheral Configuration Submenu, Irq

Page 67

Peripheral Configuration Submenu

To access this submenu, select Advanced on the menu bar, then Peripheral Configuration.

Maintenance Main

Advanced

Security Power Boot Exit

PCI Configuration

Boot Configuration

Peripheral Configuration

IDE Configuration

Diskette Configuration

Event Log Configuration

The submenu represented in Table 21 is used for configuring server peripherals.

Table 21. Peripheral Configuration Submenu

Feature

Options

Description

 

 

 

 

Serial Port A

Disabled

Configures serial port A.

 

Enabled

Auto assigns the first free COM port, normally COM1, the

 

Auto (default)

address 3F8h, and the interrupt IRQ4.

 

 

 

 

 

An * (asterisk) displayed next to an address indicates a

 

 

 

conflict with another device.

 

 

 

 

Base I/O Address

3F8 (default)

Specifies the base I/O address for serial port A, if serial

(This feature is present

2F8

port A is Enabled.

only when Serial Port A

3E8

 

is set to Enabled)

 

2E8

 

 

 

 

 

 

 

Interrupt

IRQ 3

Specifies the interrupt for serial port A, if serial port A is

(This feature is present

IRQ 4 (default)

Enabled.

only when Serial Port A

 

 

 

is set to Enabled)

 

 

 

 

 

 

 

Serial Port B

Disabled

Configures serial port B.

 

Enabled

Auto assigns the first free COM port, normally COM 2, the

 

Auto (default)

address 3F8h, and the interrupt IRQ4.

 

 

 

 

 

An * (asterisk) displayed next to an address indicates a

 

 

 

conflict with another device.

 

 

 

 

Base I/O address

2F8 (default)

Specifies the base I/O address for serial port B.

(This feature is displayed

3E8

 

only if Serial Port B is set

2E8

 

to Enabled)

 

 

 

Interrupt

IRQ 3 (default)

Specifies the interrupt for serial port B.

(This feature is displayed

IRQ 4

 

only if Serial Port B is set

 

 

 

to Enabled)

 

 

 

 

 

 

 

 

 

 

continued

Configuration Software and Utilities

67

Image 67
Contents Intel Server Board S845WD1-E Product Guide Disclaimer Contents Configuration Software and Utilities Server Board Installation and UpgradingSolving Bios Problems Tables Regulatory and Integration InformationContents Vii Viii Server Board Features Server Board FeaturesFeature Description Back Panel Connectors Back Panel ConnectorsHDD LED Front Panel ConnectorsServer Board Components Server Board Connector and Component LocationsSupported Processors Supported Memory ConfigurationsProcessors MemoryIntel 82845E Memory Controller Hub MCH Intel 845E ChipsetIntel 82801BA I/O Controller Hub ICH2 ControllerIntel 82802AB Firmware Hub FWH Diskette Drive Controller Hardware Management SubsystemSerial Ports Parallel PortChassis Intrusion and Detection Real-Time Clock, Cmos SRAM, and BatteryHardware Management Asic Fan MonitoringLegacy USB Support IDE Support Scsi Hard Drive Activity LED ConnectorIDE Interfaces PCI IDE Support PCI Auto ConfigurationLanguage Support Bios UpdatesCustom Splash Screen Recovering Bios Data CD-ROM and Network Boot Boot OptionsBooting Without Attached Devices Intel Rapid Bios Boot Fast Booting Systems with Intel Rapid Bios BootSupervisor and User Password Functions Bios Security PasswordsSmbios System Management Bios SmbiosWake on LAN Technology Power Management FeaturesWake on Ring Resume on Ring AcpiEffects of Pressing the Power Switch System States and Power StatesPower States and Targeted System Power Wake-up Devices and Events Wake-up Devices and EventsHardware Support Connector Description Power ConnectorFan Connectors Fan Connector Function/OperationInstantly Available PC Technology Location of the Standby Power Indicator LEDWake from PS/2 Devices Wake from USBPME# Wake-up Support 32-bit, 33-MHz PCI Subsystem PCI Bus CharacteristicsPCI Bus Configuration IDs PCI I/O SubsystemPCI Arbitration ATA-100Video Modes 3D Mode Refresh Rate HzVideo Mode Support with Z Buffer Enabled Video ControllerNetwork Interface Controller NIC NIC Connector and Status LEDsVideo Memory Interface Hardware Monitoring Intel Server Board S845WD1-E Product Guide Before You Begin Tools and Supplies NeededEmissions Disclaimer Intel Server Board S845WD1-E Product Guide Installing DIMMs Dimm Installation GuidelinesMemory Dimm Socket Locations Removing DIMMsO Shield Dimensions Installing the I/O ShieldLocation of the Mounting Screw Holes Installing the Server BoardInstalling the Processor in the Processor Socket Installing a ProcessorAttaching the Fan Heat Sink Clips to the Processor Socket Removing the Processor Précaution Replacing the BatteryVaro Removing the Battery Connecting the IDE Cable Connecting the IDE CableJumper Settings for the Bios Setup Program Modes Setting the Bios Configuration JumperFunction/Mode Jumper Setting Configuration Preparing for the Update Updating the Bios with the Intel Express Bios Update UtilityRecording the Current Bios Settings Obtaining the Bios Update FileCreating Bootable Media Creating a Bios Update Media Creating a Bootable DisketteUpdating the Bios Recovering the Bios Bios Setup Program Modes Using the Setup ProgramBios Setup Program Function Key Description Maintenance MenuBios Setup Program Function Keys Maintenance MenuExtended Configuration Submenu Extended Configuration SubmenuUswc Ioapic Main MenuMain Menu ECCAdvanced Menu Advanced MenuPCI Configuration Submenu PCI Configuration SubmenuBoot Configuration Submenu Boot Configuration SubmenuPeripheral Configuration Submenu Peripheral Configuration SubmenuIRQ Enabled Default Auto defaultDefault IRQ 7 defaultIDE Configuration Submenu IDE Configuration SubmenuCD-ROM Primary/Secondary IDE Master/Slave SubmenusDiskette Configuration Submenu Diskette Configuration SubmenuEvent Log Configuration Submenu Event Log Configuration SubmenuVideo Configuration Submenu Video Configuration SubmenuPCI Security Menu Security MenuAcpi Submenu Power MenuPower Menu Acpi SubmenuBoot Menu Boot MenuBoot Device Priority Submenu Boot Device Priority SubmenuAtapi CD-ROM Removable Devices Submenu Hard Disk Drives SubmenuRemovable Devices Submenu Hard Disk Drives SubmenuExit Menu Exit MenuAtapi Cdrom Drives Submenu Atapi Cdrom Drives SubmenuIntel Server Board S845WD1-E Product Guide Beep Codes Bios Beep CodesNumber of Beeps Description Bios Error Messages Bios Error MessagesError Message Explanation Nvram / Cmos / Password Intel Server Board S845WD1-E Product Guide Japan World Wide Web TelephoneU.S. and Canada Europe Asia-Pacific regionIntel Server Board S845WD1-E Product Guide Baseboard Connectors Server Board ConnectorsPower and Hardware Control Connectors Add-in Board and Peripheral Interface Connectors Add-In Board and Peripheral Interface ConnectorsSystem Memory Map Server Board ResourcesMemory Map DMA ChannelsO Map MapAddress hex Size Description Interrupts InterruptsAddress hex Description Onboard mouse port if present, else user available Product Regulatory Compliance Product Safety ComplianceProduct EMC Compliance Product Regulatory Compliance Markings Electromagnetic Compatibility NoticesProduct Certification Markings Taiwan Declaration of Conformity Europe CE Declaration of ConformityKorean RRL Compliance Installation PrecautionsAustralia / New Zealand Use Only for Intended Applications Installation RequirementsPrevent Power Supply Overload Place Battery MarkingIntel Server Board S845WD1-E Product Guide