Intel SQ599 manual CPU Internal Cache/External Cache, Quick Power On Self Test, Boot Sequence

Page 18

SQ599

and the following error message will appear, in the mean time, you can run an anti-virus program to locate the problem.

 

 

! WARNING !

 

 

 

Disk boot sector is to be modified

 

 

 

Type "Y" to accept write or "N" to abort write

 

 

 

Award Software, Inc.

 

 

 

 

Enabled

 

Activates automatically when the system boots up causing a

 

 

warning message to appear when anything attempts to access

 

 

the boot sector or hard disk partition table.

Disabled

 

No warning message to appear when anything attempts to

 

 

access the boot sector or hard disk partition table.

Note: This function is available only for DOS and other OSes that do not trap INT13.

CPU Internal Cache/External Cache

These two categories speed up memory access. However, it depends on CPU/chipset design. The default value is Enable. If your CPU without Internal Cache then this item “CPU Internal Cache” will not be show.

Enabled

Enable cache

Disabled

Disable cache

Quick Power On Self Test

These category speeds up Power On Self Test (POST) after you power on the computer. If it set to Enable, BIOS will shorten or skip some check items during POST.

Enabled

Enable quick POST

Disabled

Normal POST

Boot Sequence

This category determines which drive computer searches first for the disk Operating System (i.e., DOS). Default value is A,C.

C,A

System will first search for hard disk drive then floppy disk drive.

18

Image 18
Contents Table of Contents SVGAUTL.EXE How To Use This Manual OverviewProduct Specification BiosCPU Board Layout Memory Configuration Jumper SettingsEpom Bios Other Jumper SettingDefault Flash BiosSystem Setup PCI Device Setup Press F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Entering SetupTo Enter Setup Before Boot Press CTRL-ALT-ESC or DEL KEY Control KeyMain Manual Main MenualVGA Memory setup Standard Cmos setupBios Features setup Power Management setupStandard Cmos Setup Sector ModeDate TimeDrive C type/Drive D type Drive a type/Drive B type EGA/VGA Error haltVideo MonoBios Feature Setup Virus WarningQuick Power On Self Test Boot SequenceCPU Internal Cache/External Cache IDE HDD Block Mode Boot Up Floppy SeekBoot Up NumLock Status Gate A20 OptionSQ599 Typematic Rate Chars/Sec Typematic Rate SettingTypematic Delay Msec Security OptionSystem Bios Shadow Video Bios ShadowC8000 Cffff Shadow/E8000 Effff Shadow VGA Memory Setup VGA memory setup will appear on your screen like thisPower Management Setup Power ManagementSYN DpmsSuspend SQ599 SQ599 PCI Configuration Setup SLOT1 AutoPCI-AUTO PCIPassword Setting Password Disabled IDE HDD Auto DetectionError Messages Power-On BootBios Reference Post Message Cmos Battery has FailedCmos Checksum Error Display Switch is SET IncorrectlyDOS Utility SiS 6205 VGA FeatureInstall Program INSTDRV.EXE \instdrv EnterSVGAUTL.EXE Video Mode Table F3 Set frame rate to be n3 HzStandard Mode Mode Display Colors Frame Video Size Shades Rate Sync FreqEnhanced Mode SQ599 Page 2 OS/2 Windows SetupPower Saving Setup in Windows DefineKeySISINST.CMD OthersSET DSPADI=\ADI42\RCPSIS.EXP Enter Autodesk ADI 4.2 -Protected Mode Driver FilesAutoCAD R11 Setup ACADR11 EnterDEL C\ACADR12\ACAD.CFG RCPSIS.EXPCopy C\ADI42\RCPSIS.EXP C\ACADR12\DRV SET DSPADI=\ADI42\RCPSIS.EXPSET RCPADI=C\ADI42\RCPSIS.EXP SET RDPADI=C\ADI42\RCPSIS.EXP 3D Studio Version 3.0 Setup3DS Vibcgf Enter to configure your display environment EnterWordPerfect Graphic Mode ResolutionText Mode Resolution \3DS3\3DS EnterGEMDRV.1 GEMDRV.2 WordPerfect SetupGEM 3.0 / Ventura SDFSIS86.VGAPSIS1K.REX PcadPSIS800.REX PSIS12.REXAre you sure Y/N ? appears on the screen, keyin Enter VersaCAD/386 SetupVersaCAD/386 VCAD.1 VCAD.EORSIS1K.DRV OrCAD RelORSIS86.DRV ORSIS12.DRVOrCAD SDT.CFG Setup Lotus Lotus 1-2-3 Setup\123install Enter LOTUS.1 LOTUS.2 LOTUS.3 LOTUS.4Windows Sistag SISV.SYS SISV256.DLL SISV.DLL OEMSETUP.INFWindows NT SIS205.INF SIS205.DRV SISMINI.VXDSQ599