Intel SQ599 manual

Page 28

SQ599

 

(*) Remark 1

 

 

mode

 

 

2.

10 Sec

Defines the continuous idle time before

 

 

 

20 Sec

the system entering SUSPEND mode.

 

 

 

30 Sec

 

 

 

 

40 Sec

if any item defined in (J) is enabled &

 

 

 

1 Min

active, SUSPEND timer will be reloaded

 

 

 

3 Min

 

 

 

 

5 Min

 

 

 

 

10 Min

 

 

 

 

15 Min

 

 

 

 

20 Min

 

 

 

 

30 Min

 

 

 

 

40 Min

 

 

 

 

1 Hr

 

 

 

 

2 Hr

 

 

 

 

3 Hr

 

 

 

 

 

Note: Normally,SUSPEND

 

 

 

 

mode puts the system

 

 

 

 

into low speed or 8

 

 

 

 

MHz, clock is

 

 

 

 

stopped, screen may

 

 

 

 

be off depend on (E)

 

J. PCI Master Activity

1.

Disable

The specified event’s activity will not

 

COM Ports Activity

 

 

affect the PM timers

 

LPT Ports Activity

 

 

 

 

HDD Ports Activity

2.

Enable

The specified event’s activity causes the

 

DMA Ports Activity

 

 

PM Timers to be reloaded.

 

VGA Activity

 

 

i.e. the Power Management Unit(PMU)

 

IRQ3 (COM 2)

 

 

monitors the specified activities as PM

 

IRQ4 (COM 1)

 

 

events

 

IRQ5 (LPT 2)

 

 

 

 

IRQ6 (Floppy Disk)

 

 

 

 

IRQ7 (LPT 1)

 

 

 

 

IRQ8 (RTC Alarm)

 

 

 

 

IRQ9 (IRQ2 Redir)

 

 

 

 

IRQ10 (Reserved)

 

 

 

 

IRQ11 (Reserved)

 

 

 

 

IRQ12 (PS/2 Mouse)

 

 

 

 

IRQ13 (Coprocessor)

 

 

 

 

IRQ14 (Hard Disk)

 

 

 

28

Image 28
Contents Table of Contents SVGAUTL.EXE How To Use This Manual OverviewBios Product SpecificationCPU Board Layout Memory Configuration Jumper SettingsOther Jumper Setting DefaultEpom Bios Flash BiosSystem Setup PCI Device Setup Entering Setup To Enter Setup Before Boot Press CTRL-ALT-ESC or DEL KEYPress F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Control KeyMain Manual Main MenualStandard Cmos setup Bios Features setupVGA Memory setup Power Management setupStandard Cmos Setup Sector ModeTime DateDrive C type/Drive D type Drive a type/Drive B type Error halt VideoEGA/VGA MonoBios Feature Setup Virus WarningBoot Sequence Quick Power On Self TestCPU Internal Cache/External Cache Boot Up Floppy Seek Boot Up NumLock StatusIDE HDD Block Mode Gate A20 OptionSQ599 Typematic Rate Setting Typematic Delay MsecTypematic Rate Chars/Sec Security OptionVideo Bios Shadow System Bios ShadowC8000 Cffff Shadow/E8000 Effff Shadow VGA Memory Setup VGA memory setup will appear on your screen like thisPower Management Setup Power ManagementSYN DpmsSuspend SQ599 SQ599 PCI Configuration Setup Auto PCI-AUTOSLOT1 PCIPassword Setting Password Disabled IDE HDD Auto DetectionPower-On Boot Bios Reference Post MessageError Messages Cmos Battery has FailedCmos Checksum Error Display Switch is SET IncorrectlySiS 6205 VGA Feature Install Program INSTDRV.EXEDOS Utility \instdrv EnterSVGAUTL.EXE Video Mode Table F3 Set frame rate to be n3 HzStandard Mode Mode Display Colors Frame Video Size Shades Rate Sync FreqEnhanced Mode SQ599 Page Windows Setup Power Saving Setup in Windows2 OS/2 DefineKeySISINST.CMD OthersAutodesk ADI 4.2 -Protected Mode Driver Files AutoCAD R11 SetupSET DSPADI=\ADI42\RCPSIS.EXP Enter ACADR11 EnterRCPSIS.EXP Copy C\ADI42\RCPSIS.EXP C\ACADR12\DRVDEL C\ACADR12\ACAD.CFG SET DSPADI=\ADI42\RCPSIS.EXP3D Studio Version 3.0 Setup 3DS Vibcgf Enter to configure your display environmentSET RCPADI=C\ADI42\RCPSIS.EXP SET RDPADI=C\ADI42\RCPSIS.EXP EnterGraphic Mode Resolution Text Mode ResolutionWordPerfect \3DS3\3DS EnterWordPerfect Setup GEM 3.0 / VenturaGEMDRV.1 GEMDRV.2 SDFSIS86.VGAPcad PSIS800.REXPSIS1K.REX PSIS12.REXVersaCAD/386 Setup VersaCAD/386Are you sure Y/N ? appears on the screen, keyin Enter VCAD.1 VCAD.EOrCAD Rel ORSIS86.DRVORSIS1K.DRV ORSIS12.DRVOrCAD SDT.CFG Setup Lotus 1-2-3 Setup \123install EnterLotus LOTUS.1 LOTUS.2 LOTUS.3 LOTUS.4Sistag SISV.SYS SISV256.DLL SISV.DLL OEMSETUP.INF Windows NTWindows SIS205.INF SIS205.DRV SISMINI.VXDSQ599