Intel GA-8IPE1000 user manual Standard Cmos Features, Time

Page 32

English

2-1

Standard CMOS Features

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 

 

 

 

Standard CMOS Features

 

 

 

Date (mm:dd:yy)

Tue, Oct 26 2004

Item Help

 

Time (hh:mm:ss)

 

22:31:24

 

Menu Level`

` IDE Channel 0 Master

[None]

 

Change the day, month,

` IDE Channel 0 Slave

[None]

 

year

 

` IDE Channel 1 Master

[None]

 

 

 

` IDE Channel 1 Slave

[None]

 

<Week>

 

 

Drive A

 

[1.44M, 3.5"]

Sun. to Sat.

 

 

 

 

 

Drive B

 

[None]

 

<Month>

 

Floppy 3 Mode Suport

[Disabled]

 

Jan. to Dec.

 

Halt On

 

[All, But Keyboard]

<Day>

 

 

 

 

 

 

1 to 31 (or maximum

 

Base Memory

 

640K

 

allowed in the month)

 

Extended Memory

239M

 

 

 

 

Total Memory

 

240M

 

<Year>

 

 

 

 

 

 

1999 to 2098

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Save Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

 

Date

 

 

 

 

 

 

The date format is <week>, <month>, <day>, <year>.

 

 

 

 

Week

The week, from Sun to Sat, determined by the BIOS and is display only

 

Month

The month, Jan. Through Dec.

 

 

 

 

Day

The day, from 1 to 31 (or the maximum allowed in the month)

 

 

Year

The year, from 1999 through 2098

 

 

 

Time

The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military- time clock. For example, 1 p.m. is 13:00:00.

IDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. IDE Channel 0/1 Master/Slave IDE Device Setup. You can use one of three methods:

• Auto

Allows BIOS to automatically detect IDE devices during POST. (Default value)

• None

Select this if no IDE devices are used and the system will skip the automatic

 

detection step and allow for faster system start up.

• Manual

User can manually input the correct settings.

Access Mode

Use this to set the access mode for the hard drive. The four options are:

 

CHS/LBA/Large/Auto(default:Auto)

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information.

Cylinder

Number of cylinders

 

Head

Number of heads

 

Precomp

Write precomp

 

Landing Zone

Landing zone

 

Sector

Number of sectors

 

If a hard disk has not been installed, select NONE and press <Enter>.

 

 

GA-8IPE1000 Series Motherboard

- 32 -

Image 32
Contents GA-8IPE1000 Series Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8IPE1000 Series Motherboard Layout GA-IPE1000-G-LBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUSmsc LPC47M997-NR Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorPwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 16 IRGame Game Connector InfolinkClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckOn-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE Sata Port0 configure as Sata Port1 configure asOn-Chip Sata USB ControllerOnboard LAN Boot ROM Uart Mode SelectUR2 Duplex Mode Use IR PinsParallel Port Mode ECP Mode Use DMAOnboard Parallel port Game Port AddressModemRingOn Power Management SetupPME Event Wake Up Resume by Alarm Power on FunctionPnP/PCI Configurations INTCurrent CPU Temperature PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Memory Frequency Mhz AGP/PCI/SRC Frequency MhzDimm OverVoltage Control AGP OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Channel Audio Setup using Audio Combo Kit, optional device English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai
Related manuals
Manual 80 pages 37.27 Kb