Intel GA-8IPE1000 Onboard Parallel port, Parallel Port Mode, ECP Mode Use DMA, Game Port Address

Page 38

English

Onboard Parallel port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port.

EPP1.9+SPP

Using Parallel port as Enhanced Parallel Port 1.9 and SPP mode.

ECP

Using Parallel port as Extended Capabilities Port.

EPP1.9+ECP

Using Parallel port as Enhanced Parallel Port 1.9 and ECP mode.

PRINTER

Using Parallel port as printer port. (Default value)

EPP1.7+SPP

Using Parallel port as Enhanced Parallel Port 1.7 and SPP mode.

EPP1.7+ECP

Using Parallel port as Enhanced Parallel Port 1.7 and ECP mode.

ECP Mode Use DMA

3

Set ECP Mode Use DMA to 3. (Default value)

1

Set ECP Mode Use DMA to 1.

Game Port Address

 

201

Set Game Port Address to 201. (Default value)

209

Set Game Port Address to 209.

Disabled

Disable this function.

Midi Port Address

 

330

Set Midi Port Address to 330.

300

Set Midi Port Address to 300.

290

Set Midi Port Address to 290.

Disabled

Disable this function. (Default value)

Midi Port IRQ

 

5

Set Midi Port IRQ to 5.

10

Set Midi Port IRQ to 10. (Default value)

GA-8IPE1000 Series Motherboard

- 38 -

Image 38
Contents GA-8IPE1000 Series Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8IPE1000 Series Motherboard Layout GA-IPE1000-G-LBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUSmsc LPC47M997-NR Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorPwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 16 IRGame Game Connector InfolinkClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckOn-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE On-Chip Sata Sata Port0 configure asSata Port1 configure as USB ControllerUR2 Duplex Mode Onboard LAN Boot ROMUart Mode Select Use IR PinsOnboard Parallel port Parallel Port ModeECP Mode Use DMA Game Port AddressModemRingOn Power Management SetupPME Event Wake Up Resume by Alarm Power on FunctionPnP/PCI Configurations INTCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Dimm OverVoltage Control Memory Frequency MhzAGP/PCI/SRC Frequency Mhz AGP OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Channel Audio Setup using Audio Combo Kit, optional device English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai
Related manuals
Manual 80 pages 37.27 Kb