Intel GA-8IPE1000 user manual I/O Back Panel Introduction

Page 17

1-6 I/O Back Panel Introduction

English

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

USB port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

COM A / COM B (Serial Port)

Connects to serial-based mouse or data processing devices.

LAN Port

The provided Internet connection is Gigabit Ethernet, providing data transfer speeds of 10/100/1000Mbps.

LAN Port

The provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out

Connect the stereo speakers or earphone to this connector.

MIC In

Microphone can be connected to MIC In jack.

You can use audio software to configure 2-/4-/6-/8-channel audio functioning.

Only for GA-8IPE1000-G.

Only for GA-8IPE1000-L.

- 17 -

Hardware Installation

Image 17
Contents GA-8IPE1000 Series Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-IPE1000-G-L GA-8IPE1000 Series Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummarySmsc LPC47M997-NR Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector16 IR USB1 / FUSB2 Front USB ConnectorInfolink Game Game ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E8 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckOn-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE Sata Port1 configure as Sata Port0 configure asOn-Chip Sata USB ControllerUart Mode Select Onboard LAN Boot ROMUR2 Duplex Mode Use IR PinsECP Mode Use DMA Parallel Port ModeOnboard Parallel port Game Port AddressModemRingOn Power Management SetupPME Event Wake Up Power on Function Resume by AlarmINT PnP/PCI ConfigurationsPC Health Status Current CPU TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control AGP/PCI/SRC Frequency Mhz Memory Frequency MhzDimm OverVoltage Control AGP OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Channel Audio Setup using Audio Combo Kit, optional device English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English Taiwan Headquarters Contact UsChina Shanghai
Related manuals
Manual 80 pages 37.27 Kb