Intel GA-8IPE1000 user manual Advanced Bios Features, Hard Disk Boot Priority, Password Check

Page 34

English

2-2

Advanced BIOS Features

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 

 

 

 

Advanced BIOS Features

 

 

`

Hard Disk Boot Priority

[Press Enter]

Item Help

 

First Boot Device

[Floppy]

 

Menu Level`

 

Second Boot Device

[Hard Disk]

 

 

 

Third Boot Device

[CDROM]

 

Select Hard Disk Boot

 

Password Check

 

[Setup]

 

Device Priority

#

CPU Hyper-Threading

[Enabled]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Save Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

" # " System will detect automatically and show up when you install the Intel® Pentium® 4 processor with HT Technology.

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.

Use <> or <> to select a device, then press<+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.

First / Second / Third Boot Device

Floppy

Select your boot device priority by Floppy.

LS120

Select your boot device priority by LS120.

Hard Disk

Select your boot device priority by Hard Disk.

CDROM

Select your boot device priority by CDROM.

ZIP

Select your boot device priority by ZIP.

USB-FDD

Select your boot device priority by USB-FDD.

USB-ZIP

Select your boot device priority by USB-ZIP.

USB-CDROM

Select your boot device priority by USB-CDROM.

USB-HDD

Select your boot device priority by USB-HDD.

LAN

Select your boot device priority by LAN.

Disabled

Select your boot device priority by Disabled.

Password Check

Setup

The system will boot but will not access to Setup page if the correct password is

 

not entered at the prompt. (Default value)

System

The system will not boot and will not access to Setup page if the correct

 

password is not entered at the prompt.

CPU Hyper-Threading

Enabled

Enables CPU Hyper Threading Feature. This feature is only working for

 

operating system with multi-processors mode supported. (Default value)

Disabled

Disables CPU Hyper Threading.

 

 

GA-8IPE1000 Series Motherboard

- 34 -

Image 34
Contents GA-8IPE1000 Series Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8IPE1000 Series Motherboard Layout GA-IPE1000-G-LBlock Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUSmsc LPC47M997-NR Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorPwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 16 IRGame Game Connector InfolinkClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Set User Password „ Load Optimized Defaults „ Set Supervisor Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckOn-Chip Primary PCI IDE Integrated PeripheralsOn-Chip Secondary PCI IDE On-Chip Sata Sata Port0 configure asSata Port1 configure as USB ControllerUR2 Duplex Mode Onboard LAN Boot ROMUart Mode Select Use IR PinsOnboard Parallel port Parallel Port ModeECP Mode Use DMA Game Port AddressPME Event Wake Up Power Management SetupModemRingOn Resume by Alarm Power on FunctionPnP/PCI Configurations INTCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Dimm OverVoltage Control Memory Frequency MhzAGP/PCI/SRC Frequency Mhz AGP OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Channel Audio Setup using Audio Combo Kit, optional device English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai
Related manuals
Manual 80 pages 37.27 Kb