Intel GA-8IPE1000 Onboard LAN Boot ROM, Onboard Serial Port, Uart Mode Select, UR2 Duplex Mode

Page 37

Onboard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled

Enable this function.

Disabled

Disable this function. (Default value)

Onboard Serial Port 1

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8.

Disabled

Disable onboard Serial port 1.

Onboard Serial Port 2

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 2 and address is 3F8.

2F8/IRQ3

Enable onboard Serial port 2 and address is 2F8. (Default value)

3E8/IRQ4

Enable onboard Serial port 2 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 2 and address is 2E8.

Disabled

Disable onboard Serial port 2.

UART Mode Select

This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.

Normal

Set onboard I/O chip UART to normal mode. (Default value)

IrDA

Set onboard I/O chip UART to IrDA mode.

ASKIR

Set onboard I/O chip UART to ASKIR mode.

UR2 Duplex Mode

This feature allows you to seclect IR mode.

This function will available when "UART Mode Select" doesn't set at Normal.

Half

IR Function Duplex Half. (Default value)

Full

IR Function Duplex Full.

TxD, RxD Polarity Active

This function will available when "UART Mode Select" doesn't set at Normal.

Hi, Hi

Set TxD, RxD polarity active to Hi, Hi.

Hi, Lo

Set TxD, RxD polarity active to Hi, Lo.

Lo, Hi

Set TxD, RxD polarity active to Lo, Hi. (Default value)

Lo, Lo

Set TxD, RxD polarity active to Lo, Lo.

Use IR Pins

This function will available when "UART Mode Select" doesn't set at Normal.

RxD2, TxD2

Set IR pins to use RxD2, TxD2.

IR-Rx2Tx2

Set IR pins to use IR-Rx2Tx2. (Default value)

Only for GA-8IPE1000-G.

Only for GA-8IPE1000-L.

- 37 -

BIOS Setup

English

Image 37
Contents GA-8IPE1000 Series Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-IPE1000-G-L GA-8IPE1000 Series Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummarySmsc LPC47M997-NR Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center Connector16 IR USB1 / FUSB2 Front USB ConnectorInfolink Game Game ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E8 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckOn-Chip Primary PCI IDE Integrated PeripheralsOn-Chip Secondary PCI IDE Sata Port1 configure as Sata Port0 configure asOn-Chip Sata USB ControllerUart Mode Select Onboard LAN Boot ROMUR2 Duplex Mode Use IR PinsECP Mode Use DMA Parallel Port ModeOnboard Parallel port Game Port AddressPME Event Wake Up Power Management SetupModemRingOn Power on Function Resume by AlarmINT PnP/PCI ConfigurationsPC Health Status Current CPU TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control AGP/PCI/SRC Frequency Mhz Memory Frequency MhzDimm OverVoltage Control AGP OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Exit and Restart Remove Backup Image  Remove backup image. Are you sure? Y/NMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Channel Audio Setup using Audio Combo Kit, optional device English Spdif Output Device Optional Device Jack-Sensing and UAJ Introduction Introduction of audio connectorsAuto-detecting Enable UAJ function Manual settingUAJ Introduction Troubleshooting English English English English English Taiwan Headquarters Contact UsChina Shanghai
Related manuals
Manual 80 pages 37.27 Kb