Intel GA-8IPE1000 Memory Frequency Mhz, AGP/PCI/SRC Frequency Mhz, Dimm OverVoltage Control

Page 44

English

for FSB(Front Side Bus) frequency=800Mhz,

1.33

Memory Frequency = Host clock x 1.33.

1.6

Memory Frequency = Host clock x 1.6.

2.0

Memory Frequency = Host clock x 2.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

Memory Frequency (Mhz)

The values depend on CPU Host Frequency(Mhz) and Memory Frequency For.

AGP/PCI/SRC Frequency (Mhz)

The values depend on AGP/PCI/SRC Fixed item.

DIMM OverVoltage Control

Normal

Set DIMM OverVoltage Control to Normal. (Default value)

+0.1V

Set DIMM OverVoltage Control to +0.1V.

+0.2V

Set DIMM OverVoltage Control to +0.2V.

AGP OverVoltage Control

Normal

Set AGP OverVoltage Control to Normal. (Default value)

+0.1V

Set AGP OverVoltage Control to +0.1V.

+0.2V

Set AGP OverVoltage Control to +0.2V.

+0.3V

Set AGP OverVoltage Control to +0.3V.

CPU OverVoltage Control

Normal

Set CPU OverVoltage Control to Normal. (Default value)

+5.0%

Set CPU OverVoltage Control to +5.0%.

+7.5%

Set CPU OverVoltage Control to +7.5%.

+10.0%

Set CPU OverVoltage Control to +10.0%.

GA-8IPE1000 Series Motherboard

- 44 -

Image 44
Contents GA-8IPE1000 Series Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8IPE1000 Series Motherboard Layout GA-IPE1000-G-LBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUSmsc LPC47M997-NR Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorPwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSurcen Surround Center Connector Spdifio Spdif In / Out ConnectorUSB1 / FUSB2 Front USB Connector 16 IRGame Game Connector InfolinkClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E8 „ Load Optimized Defaults „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckOn-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE Sata Port0 configure as Sata Port1 configure asOn-Chip Sata USB ControllerOnboard LAN Boot ROM Uart Mode SelectUR2 Duplex Mode Use IR PinsParallel Port Mode ECP Mode Use DMAOnboard Parallel port Game Port AddressModemRingOn Power Management SetupPME Event Wake Up Resume by Alarm Power on FunctionPnP/PCI Configurations INTCurrent CPU Temperature PC Health StatusCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Memory Frequency Mhz AGP/PCI/SRC Frequency MhzDimm OverVoltage Control AGP OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery Unique Software UtilitiesF9 For Xpress Recovery Remove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English Channel Audio Setup using Audio Combo Kit, optional device English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting English English English English English Contact Us Taiwan HeadquartersChina Shanghai
Related manuals
Manual 80 pages 37.27 Kb