Intel GA-8I865GVMK-775 user manual Dual Channel DDR

Page 14

English

Dual Channel DDR

GA-8I865GVMK-775 supports the Dual Channel Technology. After operating the Dual Channel Technology, the bandwidth of Memory Bus will double.

GA-8I865GVMK-775 includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel A : DDR 1, DDR 2

Channel B : DDR 3, DDR 4

If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.

1.Dual channel memory cannot be used if one or three DDR memory modules are installed.

2.If two DDR memory modules are installed (same storage capacity), one must be added to the Channel A slot and the other in the Channel B slot in order to use dual channel memory. Dual channel memory cannot function if both DDR memory modules are installed on the same channel.

3.If four DDR memory modules are installed, please use memory of the same storage capacity in

order to use dual channel memory and for BIOS to detect all the DDR memory modules.

We'll strongly recommend our user to slot two DDR memory modules into the DIMMs with the same color in order for Dual Channel Technology to work.

The following table is for Dual Channel Technology combination: (DS: Double Side, SS: Single Side)

 

DDR 1

DDR 2

DDR 3

DDR 4

2 memory modules

DS/SS

X

DS/SS

X

 

X

DS/SS

X

DS/SS

4 memory modules

DS/SS

DS/SS

DS/SS

DS/SS

 

 

 

 

 

GA-8I865GVMK-775 Motherboard

- 14 -

Image 14
Contents GA-8I865GVMK-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8I865GVMK-775 Motherboard Layout GA-8I865GVMK-775Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb COM B Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory ProtectNote CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsUSB Controller Onboard LAN Boot ROMPower on Function USB 2.0 ControllerParallel Port Mode Uart Mode SelectUR2 Duplex Mode ECP Mode Use DMAPME Event Wake Up Power Management SetupAC Back Function ModemRingOn/WakeOnLanPnP/PCI Configurations Resume by AlarmPC Health Status Memory Frequency For Frequency/Voltage ControlCPU Clock Ratio Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 System requirementsLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Contact Us Taiwan HeadquartersChina Shanghai