Intel GA-8I865GVMK-775 user manual Comb COM B Connector, 16 IR

Page 25

15)COMB (COM B Connector)

Be careful with the polarity of the COMB connector. Check the pin assignment carefully while you connect the COMB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional COMB cable, please contact your local dealer.

			Pin No.	Definition
			1	NDCDB-
	2	10	2	NSINB
	2	10	3	NSOUTB
	1	9
	1	9	4	NDTRB-
			4	NDTRB-
			5	GND
			6	NDSRB-
			7	NRTSB-
			8	NCTSB-
			9	NRIB-
			10	No Pin

16)IR

Be careful with the polarity of the IR connector while you connect the IR. Please contact your nearest dealer for optional IR device.

	Pin No.	Definition
	1	Power
1	2	No Pin
1	3	IR RX
	4	GND
	5	IR TX

English

- 25 -

Hardware Installation

Image 25

Contents GA-8I865GVMK-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8I865GVMK-775 GA-8I865GVMK-775 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb COM B ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory ProtectNote CPU Enhanced Halt C1E NoteIntegrated Peripherals Sata Port1 configure asPower on Function Onboard LAN Boot ROMUSB Controller USB 2.0 ControllerUR2 Duplex Mode Uart Mode SelectParallel Port Mode ECP Mode Use DMAAC Back Function Power Management SetupPME Event Wake Up ModemRingOn/WakeOnLanResume by Alarm PnP/PCI ConfigurationsPC Health Status CPU Clock Ratio Frequency/Voltage ControlMemory Frequency For Memory Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish How to use the Xpress Recovery2 Xpress Recovery2 IntroductionUnique Software Utilities System requirementsPrecautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Taiwan Headquarters Contact UsChina Shanghai