Intel GA-8I865GVMK-775 USB Controller, USB 2.0 Controller, USB Keyboard Support, AC97 Audio

Page 35

USB Controller

Enabled	Enable USB controller. (Default value)
Disabled	Disable USB controller.

USB 2.0 Controller

You can disable this function if you are not using onboard USB 2.0 feature.

Enabled	Enable USB 2.0 controller. (Default value)
Disabled	Disable USB 2.0 controller.

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)

AC97 Audio

Auto	Auto detect AC97 audio function. (Default value)
Disabled	Disable AC97 audio function.

Onboard H/W LAN

Enabled	Enable onboard H/W LAN function. (Default value)
Disabled	Disable this function.

Onboard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled	Enable this function.
Disabled	Disable this function. (Default value)
POWER ON Function
Disabled	Disable this function. (Default value)
Any KEY	Press any key to power on the system.
Mouse	Double click on mouse left button to power on the system.
Mouse/Any KEY	Press any key or double click on mouse left button to power on the system.
Onboard Serial Port 1
Auto	BIOS will automatically setup the port 1 address.
3F8/IRQ4	Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3	Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4	Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 1.
Onboard Serial Port 2
Auto	BIOS will automatically setup the port 1 address.
3F8/IRQ4	Enable onboard Serial port 2 and address is 3F8/IRQ4.
2F8/IRQ3	Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
3E8/IRQ4	Enable onboard Serial port 2 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 2 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 2.

English

- 35 -

BIOS Setup

Image 35

Contents GA-8I865GVMK-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8I865GVMK-775 GA-8I865GVMK-775 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb COM B ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory ProtectNoteIntegrated Peripherals Sata Port1 configure asUSB 2.0 Controller Onboard LAN Boot ROMPower on Function USB ControllerECP Mode Use DMA Uart Mode SelectUR2 Duplex Mode Parallel Port ModeModemRingOn/WakeOnLan Power Management SetupAC Back Function PME Event Wake UpResume by Alarm PnP/PCI ConfigurationsPC Health Status Memory Frequency Mhz Frequency/Voltage ControlCPU Clock Ratio Memory Frequency ForLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Unique Software UtilitiesLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Taiwan Headquarters Contact UsChina Shanghai