Intel GA-8I865GVMK-775 user manual Power Management Setup, AC Back Function, PME Event Wake Up

Page 37

2-4

Power Management Setup

 

 

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

 

Power Management Setup

 

 

 

ACPI Suspend Type

 

[S1(POS)]

 

Item Help

 

Power LED in S1 state

[Blinking]

 

Menu Level`

 

Off by Power button

 

[Instant-off]

 

 

 

AC BACK Function

 

[Soft-Off]

 

 

 

 

PME Event Wake Up

[Enabled]

 

 

 

 

ModemRingOn/WakeOnLan

[Enabled]

 

 

 

 

Resume by Alarm

 

[Disabled]

 

 

 

x

Date (of Month) Alarm

Everday

 

 

 

x

Time (hh:mm:ss) Alarm

0 : 0 : 0

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

ACPI Suspend Type

 

 

 

 

 

S1(POS)

 

Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)

 

S3(STR)

 

Set ACPI suspend type to S3/STR(Suspend To RAM).

 

 

Power LED in S1 state

 

 

 

 

 

Blinking

 

In standby mode(S1), poer LED will blink. (Default value)

 

 

Dual/OFF

 

In standby mode(S1):

 

 

 

 

 

 

a. If use single color LED, power LED will turn off.

 

 

 

 

b. If use dual color LED, power LED will turn to another color.

 

 

Off by Power button

 

 

 

 

 

Instant-off

 

Press power button then Power off instantly. (Default value)

 

 

Delay 4 Sec.

Press power button 4 sec. to Power off. Enter suspend if button is pressed less than

4seconds.

AC BACK Function

Soft-Off

When AC-power back to the system, the system will be in "Off" state.

 

(Default value)

Full-On

When AC-power back to the system, the system always in "On" state.

Memory

When AC-power back to the system, the system will return to the Last state

 

before AC-power off.

PME Event Wake Up

This feature requires an ATX power supply that provides at least 1A on the 5VSB lead.

Disabled

Disable this function.

Enabled

Enable PME as wake up event. (Default value)

ModemRingOn/WakeOnLan

An incoming call via modem can awake the system from any suspend state or an input signal comes from the other client server on the LAN can awake the system from any suspend state.

Disabled

Disable Modem Ring On / Wake On LAN function.

Enabled

Enable Modem Ring On / Wake On LAN function. (Default value)

English

- 37 -

BIOS Setup

Image 37
Contents GA-8I865GVMK-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8I865GVMK-775 GA-8I865GVMK-775 Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb COM B ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Set Supervisor Password „ Load Optimized Defaults„ Set User Password „ Save & Exit SetupTime Standard Cmos FeaturesIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckLimit Cpuid Max. to CPU Hyper-ThreadingNo-Execute Memory ProtectNote CPU Enhanced Halt C1E NoteIntegrated Peripherals Sata Port1 configure asPower on Function Onboard LAN Boot ROMUSB Controller USB 2.0 ControllerUR2 Duplex Mode Uart Mode SelectParallel Port Mode ECP Mode Use DMAAC Back Function Power Management SetupPME Event Wake Up ModemRingOn/WakeOnLanResume by Alarm PnP/PCI ConfigurationsPC Health Status CPU Clock Ratio Frequency/Voltage ControlMemory Frequency For Memory Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish How to use the Xpress Recovery2 Xpress Recovery2 IntroductionUnique Software Utilities System requirementsPrecautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Taiwan Headquarters Contact UsChina Shanghai