Intel GA-8I865GVMK-775 user manual Spdif Output Device Optional Device

Page 63

SPDIF Output Device (Optional Device)

A "S/PDIF output" device is available on the motherboard. Cable with rear bracket is provided and could link to the "S/PDIF output" connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting port.

1.

Connect the SPDIF output device to the rear bracket of PC, and fix it with screw.

2.

Connect SPDIF wire to the motherboard.

3.

Connect co-axial or optical output to the AC3 decoder.

English

- 63 -

Appendix

Image 63

Contents GA-8I865GVMK-775 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8I865GVMK-775 GA-8I865GVMK-775 Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryInstallation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorPwrled BATBatteryFpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Spdif Spdif Out Connector16 IR Comb COM B ConnectorClrcmos Clear Cmos Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 „ Save & Exit Setup „ Load Optimized Defaults„ Set Supervisor Password „ Set User PasswordStandard Cmos Features TimeIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onPassword Check Advanced Bios FeaturesHard Disk Boot Priority First / Second / Third Boot DeviceCPU Enhanced Halt C1E Note CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory ProtectNoteIntegrated Peripherals Sata Port1 configure asUSB 2.0 Controller Onboard LAN Boot ROMPower on Function USB ControllerECP Mode Use DMA Uart Mode SelectUR2 Duplex Mode Parallel Port ModeModemRingOn/WakeOnLan Power Management SetupAC Back Function PME Event Wake UpResume by Alarm PnP/PCI ConfigurationsPC Health Status Memory Frequency Mhz Frequency/Voltage ControlCPU Clock Ratio Memory Frequency ForLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Unique Software UtilitiesMain Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2- / 4- / 5.1- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Taiwan Headquarters Contact UsChina Shanghai