Intel GA-8I865GVMK-775 user manual PnP/PCI Configurations, Resume by Alarm

Page 38

English

Resume by Alarm

You can set "Resume by Alarm" item to enabled and key in Date/Time to power on system.

Disabled

Disable this function. (Default value)

Enabled

Enable alarm function to POWER ON system.

If Resume by Alarm is Enabled.

Date (of Month) Alarm :

Everyday, 1~31

Time (hh: mm: ss) Alarm :

(0~23) : (0~59) : (0~59)

2-5

PnP/PCI Configurations

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

 

 

 

 

PnP/PCI Configurations

 

 

 

PCI 1 IRQ Assignment

[Auto]

 

 

Item Help

 

PCI 2 IRQ Assignment

[Auto]

 

Menu Level`

 

PCI 3 IRQ Assignment

[Auto]

 

Device(s) using this

 

 

 

 

 

 

 

 

 

 

INT:

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

PCI 1 IRQ Assignment

 

 

 

 

 

Auto

 

Auto assign IRQ to PCI 1. (Default value)

 

 

3,4,5,7,9,10,11,12,14,15

Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.

 

 

PCI 2 IRQ Assignment

 

 

 

 

 

Auto

 

Auto assign IRQ to PCI 2. (Default value)

 

 

3,4,5,7,9,10,11,12,14,15

Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.

 

 

PCI 3 IRQ Assignment

 

 

 

 

 

Auto

 

Auto assign IRQ to PCI 3. (Default value)

 

 

3,4,5,7,9,10,11,12,14,15

Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.

 

GA-8I865GVMK-775 Motherboard

- 38 -

Image 38
Contents GA-8I865GVMK-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8I865GVMK-775 Motherboard Layout GA-8I865GVMK-775Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb COM B Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory ProtectNote CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsUSB Controller Onboard LAN Boot ROMPower on Function USB 2.0 ControllerParallel Port Mode Uart Mode SelectUR2 Duplex Mode ECP Mode Use DMAPME Event Wake Up Power Management SetupAC Back Function ModemRingOn/WakeOnLanPnP/PCI Configurations Resume by AlarmPC Health Status Memory Frequency For Frequency/Voltage ControlCPU Clock Ratio Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 System requirementsLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Contact Us Taiwan HeadquartersChina Shanghai