Intel GA-8I865GVMK-775 user manual Main Screen of Xpress Recovery2, Limitations, Precautions

Page 50

English

The Main Screen of Xpress Recovery2

1. RESTORE:

 

Restore the backed-up data to your hard disk.

 

(This button will not appear if there is no backup

 

file.)

 

2. BACKUP:

 

Back up data from hard disk.

 

3. REMOVE:

 

Remove previously-created backup files

 

to release disk space.

 

(This button will not appear if there is no backup

 

file.)

 

4. REBOOT:

 

Exit the main screen and restart the system.

Limitations:

 

1.Not compatible to Xpress Recovery.

2.For the use of Xpress Recovery2, a primary partition must be reserved.

3.Xpress Recovery2 will store the backup file at the end of the hard disk, so free space available on the hard disk for the backup file must be allocated in advance. (A minimum 4GB is recom- mended but the actual space is dependent on the size of the data to be backed up)

4.Capable of backing up hard disks installed with Windows operating systems including DOS and Windows XP/2000/NT/9x/Me.

5.USB hard disks are currently not supported.

6.Does not support RAID/AHCI (class code 0104/0106) hard disks.

7.Capable of backing up and restoring only the first physical hard disk.

Hard disks detection sequence is as follows:

a.PATA IDE primary channel

b.PATA IDE secondary channel

c. SATA IDE channel 1

d.SATA IDE channel 2

e.SATA IDE channel 3

f.SATA IDE channel 4

Precautions:

1.When using hard disks with more than 128G under Windows 2000, be sure to execute the EnableBigLba.exe program from the driver CD before data backup.

2.It is normal that data backup takes longer time than data restoration.

3.Xpress Recovery2 is compliant with the GPL regulations.

4.On a few motherboards based on Nvidia chipsets, BIOS update is required for Xpress Recovery2 to correctly identify RAID and SATA IDE mode. Please contact your motherboard manufacturer.

5.Xpress Recovery2 supports only PATA hard disks and not SATA hard disks on the following motherboards (As this is a BIOS-related issue, it can be solved by BIOS update)

GA-K8U

GA-K8NXP-9

 

GA-8N-SLI Royal

GA-K8U-9

GA-K8N Ultra-9

GA-8N-SLI Pro

GA-K8NXP-SLI

GA-K8NF-9 (PCB Ver. 1.0)

GA-8N-SLI

GA-K8N Ultra-SLI

GA-K8NE (PCB Ver. 1.0)

 

GA-K8N Pro-SLI

GA-K8NMF-9

 

 

GA-8I865GVMK-775 Motherboard

- 50 -

 

Image 50
Contents GA-8I865GVMK-775 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-8I865GVMK-775 Motherboard Layout GA-8I865GVMK-775Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUInstallation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorBATBattery PwrledFpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorSpdif Spdif Out Connector USB1 / FUSB2 Front USB ConnectorComb COM B Connector 16 IRClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 „ Set User Password „ Load Optimized Defaults„ Set Supervisor Password „ Save & Exit SetupIDE Channel 0 Master, Slave / IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password CheckNo-Execute Memory ProtectNote CPU Hyper-ThreadingLimit Cpuid Max. to CPU Enhanced Halt C1E NoteSata Port1 configure as Integrated PeripheralsUSB Controller Onboard LAN Boot ROMPower on Function USB 2.0 ControllerParallel Port Mode Uart Mode SelectUR2 Duplex Mode ECP Mode Use DMAPME Event Wake Up Power Management SetupAC Back Function ModemRingOn/WakeOnLanPnP/PCI Configurations Resume by AlarmPC Health Status Memory Frequency For Frequency/Voltage ControlCPU Clock Ratio Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 System requirementsLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings 3 2- / 4- / 5.1- Channel Audio Function IntroductionChannel Audio Setup English Spdif Output Device Optional Device Troubleshooting English English English English English English Contact Us Taiwan HeadquartersChina Shanghai