Intel EK-KZPCM-UG manual Kzpcm Host Adapter Features, Specifications

Page 17

Chapter 1. Product Description

1.3KZPCM Host Adapter Features

Some of the significant features of the Host Adapter are:

Direct PCI connection for simplicity and reliability

Ultra-wide SCSI/Ethernet device protocol

Dual single-ended SCSI channels

Support for Fast, Wide, and Ultra-wide SCSI devices

Plug-and-play support for up to 30 SCSI devices (for Intel platforms only)

Up to 80 Mb/sec SCSI synchronous data rate

SCAM (SCSI Configured Automatically) protocol

Direct memory access for low-overhead burst data transfers over 100 Mbytes/second

Concurrent I/O and 10/100 Base-T Ethernet operations

State-of-the-art software drivers for Intel- and Alpha-based servers

1.4Specifications

Table 1-1 lists some significant specifications of the KZPCM Host Adapter.

EK–KZPCM–UG. B01

1–3

Image 17
Contents User’s Guide Achtung Page Page Contents Digital OpenVMS Installation Windows NT InstallationDigital Unix Installation Ethernet Description and ConfigurationTables Page Revision Level Date Summary of Changes Revision RecordPage Visit our Web Site for the Latest Information About This GuideAudience Related DocumentationBoldface type ConventionsWho to contact in Asia Pacific Support and Services Who to contact in the AmericasWho to contact in Europe Page Functional Description Product DescriptionPhysical Description Specifications Kzpcm Host Adapter FeaturesSpecifications Installation Overview Installing the Kzpcm Host AdapterGetting Started User-Supplied Hardware and Software RequirementsTerminating the Scsi Buses Kzpcm Host Adapter Kit ContentsBack up Your System Kzpcm Host Adapter PCB Components Setting Scsi Device IDs Inserting the Host Adapter in a Chassis Slot Installing the Host AdapterInserting the Host Adapter in a Slot Connecting Internal Scsi DevicesInstalling the 68-pin Cable Connector Onto the Host Adapter Installing the 50-pin Cable Connector Onto the Host Adapter Connecting the Ribbon Cable to an Internal Scsi Device Connecting the Ribbon Cable to a Second Internal Scsi Device Connecting External Scsi DevicesConnecting an External Scsi Cable to the Host Adapter Cabling for Typical Configurations Configuration, 16-bit Internal Devices Only 10 Configuration, 16-bit Internal and 8-bit Devices Channel a 16 B it Channel B 16 Bit ID = Page Starting the On-board Configuration Utility Bios Configuration UtilityNvram Descriptions of the Main Menu SelectionsSelected Adapter Utilities Menu Adapter Setup MenuDevice Selections Device Specific Parameter Menu Parameter Settings Quick Reference Chart Exiting the Configuration UtilityParameter Console Operating System SRM Page SYMC8XX.SYS Miniport Driver Description Windows NT InstallationInstalling the SYMC8XX.SYS Miniport Driver No Scsi Devices Are Found During Installation TroubleshootingProblems With Ultra Devices Using Ultra Protocol Digital OpenVMS Driver Description Digital OpenVMS InstallationDigital OpenVMS, Version 7.1-1H1 Only Installing the Digital OpenVMS DriverBoot -flag 0,80000 dka400,dkb0,dva0 Sys$systemsys$config.dat Sys$systemsys$userconfig.datType in DVA0 $ shutdown Set bootdefdev dkb0 Set bootosflags 0,0 Boot $ reboot $ product install ITI3140Digital OpenVMS, Version 7.1-1H2 or Higher $ mount dva0 3pbkitFrom the system SRM console boot the CD-ROM drive as follows Changing the Scsi ID of the Host Adapter VMS Digital Unix Driver Description Digital Unix InstallationDriver Installation Installing the Digital Unix Driver#/usr/opt/ITPSA100/conf/itconfig.sh Syscfgfile Addition of New Hardware After Kzpcm Installation#/usr/opt/ITPSA100/data/itconfig.dat Bus Re-numberingExample # uerf -R -r 300 more# cd /sys/SYSCFGFILE # cp vmunix /vmunix # cd /sys/conf # doconfig -c Syscfgfile# cp /vmunix /vmunix.orig Setting the Adapter ID Under the Unix Operating System Setting the Host Adapter Scsi ID UnixSetting the Host Adapter ID at the System Console #shutdown -r now #cd /sys/$SYSCFGNAME #cp vmunix /vmunixPage Kzpcm Host Adapter Ethernet Option Features Ethernet Description and ConfigurationDisplaying and Setting Ethernet Port Characteristics P0 Set Ewn0modeInitial System Installation System Installation for Windows NT on Ethernet OptionExisting System Installation Show Ewn0modeEthernet Description and Configuraton Page Locating the Kzpcm Host Adapter in the System Kzpcm Host Adapter DiagnosticsShow config Seagate ST31055W Set pkb0hostid 6 ! Scsi bus port B Determining the Kzpcm Host Scsi IDShow dev Disk Drives with the Same ID as the Host Locating Scsi Device ID ConflictsTwo Disk Drives with the Same ID Checking the Scsi Bus Termination Testing the Scsi PortsExer dkb ShowstatusShow ewa0mode Testing the EthernetNettest ewa0 -mode internal -pass Showstatus KilldiagEK-KZPCM-UG. B01 Reader’s Comments