Intel EK-KZPCM-UG manual Installing the Kzpcm Host Adapter, Installation Overview, Getting Started

Page 19

2

Installing the KZPCM Host Adapter

This chapter tells you how to terminate the SCSI buses, how to set SCSI IDs, how to install the Host Adapter in your computer, and how to connect internal and external SCSI devices to the adapter.

2.1Installation Overview

The installation of the KZPCM Host Adapter consists of the following steps:

Terminating the SCSI buses.

Installing the Host Adapter module in your computer.

Connecting internal or external SCSI devices to the adapter.

2.2Getting Started

Before starting the installation, do the following:

Check that you have the necessary user-supplied hardware and software (refer to Subsection 2.2.1).

Inventory the contents of the KZPCM Host Adapter kit

Back up the computer system

2.2.1 User-Supplied Hardware and Software Requirements

The KZPCM Host Adapter requires the following user-supplied hardware and software:

An AXP- or Intel-based computer system with a PCI local bus, a 3½-inch (1.44 MB) floppy drive, an available PCI slot, disk space to load software drivers, and the associated system hardware manual

The SCSI cables necessary to connect SCSI devices to the adapter module

One of the following operating systems:

Windows NT, version 4.0 or higher

DIGITAL OpenVMS, version 7.1-1H1 or higher

DIGITAL UNIX, version 4.0d or higher

Alpha firmware upgrade CD5.0.

EK–KZPCM–UG. B01

2–1

Image 19
Contents User’s Guide Achtung Page Page Contents Ethernet Description and Configuration Windows NT InstallationDigital OpenVMS Installation Digital Unix InstallationTables Page Revision Level Date Summary of Changes Revision RecordPage Related Documentation About This GuideVisit our Web Site for the Latest Information AudienceBoldface type ConventionsWho to contact in Europe Support and Services Who to contact in the AmericasWho to contact in Asia Pacific Page Functional Description Product DescriptionPhysical Description Specifications Kzpcm Host Adapter FeaturesSpecifications User-Supplied Hardware and Software Requirements Installing the Kzpcm Host AdapterInstallation Overview Getting StartedBack up Your System Kzpcm Host Adapter Kit ContentsTerminating the Scsi Buses Kzpcm Host Adapter PCB Components Setting Scsi Device IDs Inserting the Host Adapter in a Chassis Slot Installing the Host AdapterInserting the Host Adapter in a Slot Connecting Internal Scsi DevicesInstalling the 68-pin Cable Connector Onto the Host Adapter Installing the 50-pin Cable Connector Onto the Host Adapter Connecting the Ribbon Cable to an Internal Scsi Device Connecting the Ribbon Cable to a Second Internal Scsi Device Connecting External Scsi DevicesConnecting an External Scsi Cable to the Host Adapter Cabling for Typical Configurations Configuration, 16-bit Internal Devices Only 10 Configuration, 16-bit Internal and 8-bit Devices Channel a 16 B it Channel B 16 Bit ID = Page Starting the On-board Configuration Utility Bios Configuration UtilityNvram Descriptions of the Main Menu SelectionsSelected Adapter Utilities Menu Adapter Setup MenuDevice Selections Device Specific Parameter Menu Parameter Settings Quick Reference Chart Exiting the Configuration UtilityParameter Console Operating System SRM Page SYMC8XX.SYS Miniport Driver Description Windows NT InstallationInstalling the SYMC8XX.SYS Miniport Driver No Scsi Devices Are Found During Installation TroubleshootingProblems With Ultra Devices Using Ultra Protocol Digital OpenVMS Driver Description Digital OpenVMS InstallationDigital OpenVMS, Version 7.1-1H1 Only Installing the Digital OpenVMS DriverBoot -flag 0,80000 dka400,dkb0,dva0 Sys$systemsys$config.dat Sys$systemsys$userconfig.datType in DVA0 $ shutdown Set bootdefdev dkb0 Set bootosflags 0,0 Boot $ mount dva0 3pbkit $ product install ITI3140$ reboot Digital OpenVMS, Version 7.1-1H2 or HigherFrom the system SRM console boot the CD-ROM drive as follows Changing the Scsi ID of the Host Adapter VMS Digital Unix Driver Description Digital Unix InstallationDriver Installation Installing the Digital Unix DriverBus Re-numbering Addition of New Hardware After Kzpcm Installation#/usr/opt/ITPSA100/conf/itconfig.sh Syscfgfile #/usr/opt/ITPSA100/data/itconfig.datExample # uerf -R -r 300 more# cp /vmunix /vmunix.orig # cd /sys/conf # doconfig -c Syscfgfile# cd /sys/SYSCFGFILE # cp vmunix /vmunix Setting the Host Adapter ID at the System Console Setting the Host Adapter Scsi ID UnixSetting the Adapter ID Under the Unix Operating System #shutdown -r now #cd /sys/$SYSCFGNAME #cp vmunix /vmunixPage P0 Set Ewn0mode Ethernet Description and ConfigurationKzpcm Host Adapter Ethernet Option Features Displaying and Setting Ethernet Port CharacteristicsShow Ewn0mode System Installation for Windows NT on Ethernet OptionInitial System Installation Existing System InstallationEthernet Description and Configuraton Page Show config Kzpcm Host Adapter DiagnosticsLocating the Kzpcm Host Adapter in the System Seagate ST31055W Show dev Determining the Kzpcm Host Scsi IDSet pkb0hostid 6 ! Scsi bus port B Two Disk Drives with the Same ID Locating Scsi Device ID ConflictsDisk Drives with the Same ID as the Host Showstatus Testing the Scsi PortsChecking the Scsi Bus Termination Exer dkbKilldiag Testing the EthernetShow ewa0mode Nettest ewa0 -mode internal -pass ShowstatusEK-KZPCM-UG. B01 Reader’s Comments