Intel EK-KZPCM-UG manual Connecting Internal Scsi Devices, Inserting the Host Adapter in a Slot

Page 24

KZPCM PCI–to–Dual Channel Ultra SCSI and 10/100MB Ethernet Host Adapter

Figure 2–2 Inserting the Host Adapter in a Slot

2.5.2 Connecting Internal SCSI Devices

Refer to your SCSI device documentation if you want to install one or more SCSI device inside the host computer. The internal device(s) must be single- ended.

To connect an internal SCSI device to the KZPCM Host Adapter, you will need one, or both, of the following cables depending on the requirements of your internal drive.

∙A 50-pin connector SCSI ribbon cable with a 50-pin header internal connector to mate with the Host Adapter 50-pin connector

∙A 68-pin connector SCSI cable with a 68-pin header internal connector to mate with the Host Adapter 68-pin connector

2–6	EK–KZPCM–UG. B01

Image 24

Contents User’s Guide Achtung Page Page Contents Windows NT Installation Digital OpenVMS InstallationDigital Unix Installation Ethernet Description and ConfigurationTables Page Revision Record Revision Level Date Summary of ChangesPage About This Guide Visit our Web Site for the Latest InformationAudience Related DocumentationConventions Boldface typeSupport and Services Who to contact in the Americas Who to contact in EuropeWho to contact in Asia Pacific Page Product Description Functional DescriptionPhysical Description Kzpcm Host Adapter Features SpecificationsSpecifications Installing the Kzpcm Host Adapter Installation OverviewGetting Started User-Supplied Hardware and Software RequirementsKzpcm Host Adapter Kit Contents Back up Your SystemTerminating the Scsi Buses Kzpcm Host Adapter PCB Components Setting Scsi Device IDs Installing the Host Adapter Inserting the Host Adapter in a Chassis SlotConnecting Internal Scsi Devices Inserting the Host Adapter in a SlotInstalling the 68-pin Cable Connector Onto the Host Adapter Installing the 50-pin Cable Connector Onto the Host Adapter Connecting the Ribbon Cable to an Internal Scsi Device Connecting External Scsi Devices Connecting the Ribbon Cable to a Second Internal Scsi DeviceConnecting an External Scsi Cable to the Host Adapter Cabling for Typical Configurations Configuration, 16-bit Internal Devices Only 10 Configuration, 16-bit Internal and 8-bit Devices Channel a 16 B it Channel B 16 Bit ID = Page Bios Configuration Utility Starting the On-board Configuration UtilityDescriptions of the Main Menu Selections NvramAdapter Setup Menu Selected Adapter Utilities MenuDevice Selections Device Specific Parameter Menu Exiting the Configuration Utility Parameter Settings Quick Reference ChartParameter Console Operating System SRM Page Windows NT Installation SYMC8XX.SYS Miniport Driver DescriptionInstalling the SYMC8XX.SYS Miniport Driver Troubleshooting No Scsi Devices Are Found During InstallationProblems With Ultra Devices Using Ultra Protocol Digital OpenVMS Installation Digital OpenVMS Driver DescriptionInstalling the Digital OpenVMS Driver Digital OpenVMS, Version 7.1-1H1 OnlySys$systemsys$config.dat Sys$systemsys$userconfig.dat Boot -flag 0,80000 dka400,dkb0,dva0Type in DVA0 $ shutdown Set bootdefdev dkb0 Set bootosflags 0,0 Boot $ product install ITI3140 $ rebootDigital OpenVMS, Version 7.1-1H2 or Higher $ mount dva0 3pbkitFrom the system SRM console boot the CD-ROM drive as follows Changing the Scsi ID of the Host Adapter VMS Digital Unix Installation Digital Unix Driver DescriptionInstalling the Digital Unix Driver Driver InstallationAddition of New Hardware After Kzpcm Installation #/usr/opt/ITPSA100/conf/itconfig.sh Syscfgfile#/usr/opt/ITPSA100/data/itconfig.dat Bus Re-numbering# uerf -R -r 300 more Example# cd /sys/conf # doconfig -c Syscfgfile # cp /vmunix /vmunix.orig# cd /sys/SYSCFGFILE # cp vmunix /vmunix Setting the Host Adapter Scsi ID Unix Setting the Host Adapter ID at the System ConsoleSetting the Adapter ID Under the Unix Operating System #cd /sys/$SYSCFGNAME #cp vmunix /vmunix #shutdown -r nowPage Ethernet Description and Configuration Kzpcm Host Adapter Ethernet Option FeaturesDisplaying and Setting Ethernet Port Characteristics P0 Set Ewn0modeSystem Installation for Windows NT on Ethernet Option Initial System InstallationExisting System Installation Show Ewn0modeEthernet Description and Configuraton Page Kzpcm Host Adapter Diagnostics Show configLocating the Kzpcm Host Adapter in the System Seagate ST31055W Determining the Kzpcm Host Scsi ID Show devSet pkb0hostid 6 ! Scsi bus port B Locating Scsi Device ID Conflicts Two Disk Drives with the Same IDDisk Drives with the Same ID as the Host Testing the Scsi Ports Checking the Scsi Bus TerminationExer dkb ShowstatusTesting the Ethernet Show ewa0modeNettest ewa0 -mode internal -pass Showstatus KilldiagReader’s Comments EK-KZPCM-UG. B01