Intel EK-KZPCM-UG manual Seagate ST31055W

Page 68

KZPCM PCI–to–Dual Channel Ultra SCSI and 10/100MB Ethernet Host Adapter

Digital Equipment Corporation

AlphaServer 1000A 5/300

Firmware
SRM Console:		V5.0-101
ARC Console:		v5.31
PALcode: VMS PALcode V1.19-4, OSF PALcode V1.21-6
Serial Rom:		V1.0
Processor
DECchip (tm) 21164-5			300MHz
Memory
	64 Meg of System Memory
	Bank 0 = 32 Mbytes(8 MB Per SIMM) Starting at 0x00000000
	Bank 1 = 32 Mbytes(8 MB Per SIMM) Starting at 0x02000000
	Bank 2 = No Memory Detected
	Bank 3 = No Memory Detected
Slot Option			Hose 0, Bus 0, PCI
7	Intel 82375			Bridge to Bus 1, EISA
8	DECchip 21050-AA			Bridge to Bus 2, PCI
11	000C1000/10001000
12	DECchip 21152-AA			Bridge to Bus 3, PCI
Slot Option			Hose 0, Bus 1, EISA
Slot Option			Hose 0, Bus 3, PCI
0	NCR 53C875		pkb0.7.0.3000.0	SCSI Bus ID 7
			dkb0.0.0.3000.0	SEAGATE ST31055W
1	NCR 53C875		pkc0.7.0.3001.0	SCSI Bus ID 7
2	DE500-AA Network Con ewa0.0.0.3002.0			00-06-2B-00-04-8B

Note that the last entry, Hose 0, Bus 3, PCI, consists of two 53C875 devices and a DE500-AA device. This last entry is the KZPCM Host Adapter in this system. This can be verified by the MAC address (00-06-2B-00-04-8B in the example above), which is attached to the module with a label. Write down

8–2	EK–KZPCM–UG. B01

Image 68

Contents User’s Guide Achtung Page Page Contents Windows NT Installation Digital OpenVMS InstallationDigital Unix Installation Ethernet Description and ConfigurationTables Page Revision Record Revision Level Date Summary of ChangesPage About This Guide Visit our Web Site for the Latest InformationAudience Related DocumentationConventions Boldface typeWho to contact in Asia Pacific Support and Services Who to contact in the AmericasWho to contact in Europe Page Product Description Functional DescriptionPhysical Description Kzpcm Host Adapter Features SpecificationsSpecifications Installing the Kzpcm Host Adapter Installation OverviewGetting Started User-Supplied Hardware and Software RequirementsTerminating the Scsi Buses Kzpcm Host Adapter Kit ContentsBack up Your System Kzpcm Host Adapter PCB Components Setting Scsi Device IDs Installing the Host Adapter Inserting the Host Adapter in a Chassis SlotConnecting Internal Scsi Devices Inserting the Host Adapter in a SlotInstalling the 68-pin Cable Connector Onto the Host Adapter Installing the 50-pin Cable Connector Onto the Host Adapter Connecting the Ribbon Cable to an Internal Scsi Device Connecting External Scsi Devices Connecting the Ribbon Cable to a Second Internal Scsi DeviceConnecting an External Scsi Cable to the Host Adapter Cabling for Typical Configurations Configuration, 16-bit Internal Devices Only 10 Configuration, 16-bit Internal and 8-bit Devices Channel a 16 B it Channel B 16 Bit ID = Page Bios Configuration Utility Starting the On-board Configuration UtilityDescriptions of the Main Menu Selections NvramAdapter Setup Menu Selected Adapter Utilities MenuDevice Selections Device Specific Parameter Menu Exiting the Configuration Utility Parameter Settings Quick Reference ChartParameter Console Operating System SRM Page Windows NT Installation SYMC8XX.SYS Miniport Driver DescriptionInstalling the SYMC8XX.SYS Miniport Driver Troubleshooting No Scsi Devices Are Found During InstallationProblems With Ultra Devices Using Ultra Protocol Digital OpenVMS Installation Digital OpenVMS Driver DescriptionInstalling the Digital OpenVMS Driver Digital OpenVMS, Version 7.1-1H1 OnlySys$systemsys$config.dat Sys$systemsys$userconfig.dat Boot -flag 0,80000 dka400,dkb0,dva0Type in DVA0 $ shutdown Set bootdefdev dkb0 Set bootosflags 0,0 Boot $ product install ITI3140 $ rebootDigital OpenVMS, Version 7.1-1H2 or Higher $ mount dva0 3pbkitFrom the system SRM console boot the CD-ROM drive as follows Changing the Scsi ID of the Host Adapter VMS Digital Unix Installation Digital Unix Driver DescriptionInstalling the Digital Unix Driver Driver InstallationAddition of New Hardware After Kzpcm Installation #/usr/opt/ITPSA100/conf/itconfig.sh Syscfgfile#/usr/opt/ITPSA100/data/itconfig.dat Bus Re-numbering# uerf -R -r 300 more Example# cd /sys/SYSCFGFILE # cp vmunix /vmunix # cd /sys/conf # doconfig -c Syscfgfile# cp /vmunix /vmunix.orig Setting the Adapter ID Under the Unix Operating System Setting the Host Adapter Scsi ID UnixSetting the Host Adapter ID at the System Console #cd /sys/$SYSCFGNAME #cp vmunix /vmunix #shutdown -r nowPage Ethernet Description and Configuration Kzpcm Host Adapter Ethernet Option FeaturesDisplaying and Setting Ethernet Port Characteristics P0 Set Ewn0modeSystem Installation for Windows NT on Ethernet Option Initial System InstallationExisting System Installation Show Ewn0modeEthernet Description and Configuraton Page Locating the Kzpcm Host Adapter in the System Kzpcm Host Adapter DiagnosticsShow config Seagate ST31055W Set pkb0hostid 6 ! Scsi bus port B Determining the Kzpcm Host Scsi IDShow dev Disk Drives with the Same ID as the Host Locating Scsi Device ID ConflictsTwo Disk Drives with the Same ID Testing the Scsi Ports Checking the Scsi Bus TerminationExer dkb ShowstatusTesting the Ethernet Show ewa0modeNettest ewa0 -mode internal -pass Showstatus KilldiagReader’s Comments EK-KZPCM-UG. B01