Lenovo 6423, 6493, 6483, 6449 Selecting or changing the startup device sequence, Advanced settings

Page 29

3.Select the desired startup device from the Startup Device Menu and press Enter to begin.

Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence.

Selecting or changing the startup device sequence

To view or permanently change the configured startup device sequence, do the following:

1.Start the Setup Utility program (see “Starting the Setup Utility program” on page 19).

2.Select Startup Startup Sequence, and see the information displayed on the right side of the screen.

3.Select the devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error Startup Sequence.

4.Select Exit from the Setup Utility menu and then Save Settings or Save and exit the Setup Utility.

If you have changed these settings and want to return to the default settings, select Load Default Settings on the Exit menu.

Advanced settings

On some computer models, the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This feature works only with HyperThreading-aware operating systems, such as Windows XP. The default setting for HyperThreading is Enabled. However, if you select Set Defaults and are using an operating system other than Windows XP, your computer performance might be degraded. Therefore, you should always set HyperThreading to Disabled unless you are sure your operating system supports HyperThreading.

Exiting from the Setup Utility program

After you finish viewing or changing settings, press Esc to return to the Setup Utility program menu (you might have to press Esc several times). If you want to save the new settings, select Save Settings or Save and exit the Setup Utility. Otherwise, your changes will not be saved.

Chapter 5. Using the Setup Utility 21

Image 29
Contents Page Page ThinkStation User Guide Page Contents Appendix A. Manual modem Appendix B. Notices Commands Introduction Vi User Guide Additional safety requirements for machine types 6427, 6449, Important safety informationUser Guide Glare and lighting Arranging your workspaceComfort Electrical outlets and cable lengths Air circulationConnecting your computer Setting up your computerUser Guide Setting up your computer Phone Line Setting up your computer 1394 Completing important tasks Turning on computer powerFinishing the software installation Installing external options Installing other operating systemsUpdating your operating system Updating your antivirus softwareSystem information FeaturesInput/output features Operating systems, preinstalled varies by model Environment SpecificationsSoftware provided with your Windows operating system Software overviewSoftware provided by Lenovo PC-Doctor for WINPE, PC-Doctor for WindowsAdobe Acrobat Reader Starting the Setup Utility program Using the Setup UtilityViewing and changing settings Using passwordsAdministrator Password User PasswordSetting, changing, and deleting a password Selecting a startup deviceSelecting or changing the startup device sequence Advanced settingsExiting from the Setup Utility program User Guide Attaching Sata hard disk drives Installing and configuring RAIDCreating RAID volumes Supported SAS RAID configurations Deleting RAID volumesInstalling and configuring RAID Properties Installing and configuring RAID User Guide Updating system programs Using system programsUpdating flashing Bios from a diskette or CD-ROM Updating flashing Bios from your operating system Basic troubleshooting Troubleshooting and diagnosticsDiagnostic programs PC-Doctor for DOS PC-Doctor for WindowsPC-Doctor for Windows PE Creating a diagnostic CD image Non-optical mouse Cleaning the mouseOptical mouse 1 Retainer ring 2 Ball 3 Plastic rollers 4 Ball cage Creating and using the Product Recovery disc Recovering softwarePerforming backup and recovery operations Using the Rescue and Recovery workspace Creating and using rescue media To create rescue media, do the following Creating and using a Recovery Repair disketteRecovering or installing device drivers Solving recovery problems Setting a rescue device in the startup sequenceUser Guide Information resources Getting information, help, and serviceOnline Books folder ThinkVantage Productivity CenterUsing the documentation and diagnostic programs Safety and WarrantyHelp and service Using other services Calling for servicePurchasing additional services Basic AT commands Appendix A. Manual modem commandsLow speaker volume Enable RTS/CTS hardware flow control Extended AT commands+MS=? MNP/V.42/V.42bis/V.44 commandsFax Class 2 commands Fax Class 1 commandsVoice commands Appendix A. Manual modem commands User Guide Appendix B. Notices Trademarks Television output noticeIndex Page Using User Guide Page Part Number 43C9722