Sanyo PLV-Z60 Cleaning, Panel adjustment, Highland, Lamp counter reset, Factory default

Page 40

Setting

Cleaning

This function is used to clean the inside of the projector. Using a blower as well is more effective. See page 44.

Press the Point 8or OK buttons, then the projected image is blacked out temporarily regardless of whether or not an input source is selected. The fans start to operate automatically to help blowing the dust.

To cancel the cleaning function, set the projector back into the right position, then press any other button during cleaning operations.

Note:

• The Power management function cannot be operated during cleaning.

Panel adjustment

This function is used to get the best picture reproduction of the R (red), G (green), and B (blue) LCD panels. If the proper adjustment is not made, you might get vertical noise lines on the screen.

This function should be made more than 10 minutes after turning on the projector with or without any signal.

A dark environment helps make more accurate adjustment.

Press the OK button or Point 8 button and the Test pattern screens will appear in the order of R (red), G (green), and B (blue). Use the Point ed78 buttons to adjust each pattern as follows:

1.Adjust the value in the Bright dialog box to minimize vertical lines in the bright part of the picture.

2.Adjust the value in the Dark dialog box to minimize vertical lines in the dark part of the picture.

3.Press the Point ed buttons to move on to the next color. Repeat step 1 and 2 for each R,G,B panel until the vertical lines of the picture are minimized.

4.Press the Point ed buttons to display the Check pattern screen and check the adjustment.

5.To close this screen and return to the menu, press the OK or MENU button.

Highland

When using the projector in high altitudes (about 1,200 meters or more above the sea level), set this function “On.” Press the Point

8or OK buttons to switch On/Off.

Lamp counter reset

This function resets the lamp replacement counter. When replacing the projection lamp, reset the lamp replacement counter with this function. See page 48 for operation.

Factory default

This function restores all setting values except for the user’s logo and the lamp counter to the factory default settings.

1. Adjust the bright parts with the Bright dialog box.

2. Adjust the dark parts with the Dark dialog box.

3.Then adjust the Test pattern G and Test pattern B in the same way.

4.Check the adjustment with Check pattern screen.

Factory default

Select Factory default and press the OK or Point 8 buttons. “Return to Factory default?” appears.

Select [Yes] and press the OK button, then another confirmation box appears.

Select [Yes] again to restore to the factory default settings.

40

Image 40
Contents Model PLV-Z60 Features and Design Short Throw & Wide-Range Zoom Lens Automatic Slide ShutterTable of Contents To the Owner Please help us to conserve the environment we liveSafety Instructions Voor de klanten in NederlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticePart Names and Functions FrontBack BottomRear Terminal Top Control Remote Control Remote Control Operating Range Remote Control Battery InstallationAdjustable Feet InstallationPositioning the Projector Connecting the AC Power Cord For the U.KFor the U.S.A. and Canada For Continental Europe 120V ACBefore using Moving the LensHorizontal Lens Shift Left/Right Lens Shift RingsConnecting to Video Equipment Video, S-Video Connecting to Video Equipment ComponentVideo, S-video ComponentConnecting to Video Equipment HDMI, RGB Scart Connecting to a ComputerRGB Scart Computer AnalogTop Control Remote Control Main On/Off switch Basic OperationTurning On the Projector Selected Input Source Automatic Slide ShutterTurning Off the Projector How to Operate the On-Screen Menu Top Control Remote ControlOn-Screen Menu Main Menu On-Screen Menu SubmenuMenu and its Functions Zoom and Focus Adjustment Remote Control OperationLight button Freeze buttonReset button Screen buttonNo Show button Image ADJ. buttonInput Input buttons on the remote controlInput Source and System Selection Video or S-Video Menu OperationComponent 1 or Component Hdmi 1 or Hdmi ComputerRGB Analog Source Select MenuImage Image Mode SelectionDirect Operation Image Adjustment Image Mode AdjustmentWhite balance Red White balance GreenWhite balance Blue SharpnessAdvanced menu Lamp irisAuto black stretch Contrast enhancementColor Management Color management pointerReset StorePicture Adjustment Picture Position and Screen AdjustmentScreen Size Adjustment ScreenCaption NormalNormal through Natural wideSetting SettingHdmi setup Off Normal Hdmi setup BackgroundMounting RearPower off confirmation DisplayLogo CaptureTo change the code of the remote control Power managementTo change the code of the projector Shutter demoCleaning Panel adjustmentLamp counter reset Factory defaultInformation Input Source Information DisplayMaintenance and Cleaning Then check the items belowCleaning the RGB panels If the nozzle is pulled outWhich hole to put the nozzle in? Cleaning the Air Filters Cleaning the Projection Lens Cleaning the Projector CabinetReset the Lamp replacement counter Lamp ReplacementSee Lamp Replacement Counter on the next Lamp Replacement Counter Troubleshooting AppendixIndicators and Projector Condition Menu Tree Input ImagePicture adj Screen Information System Mode Chart System mode Freq KHzTechnical Specifications Configurations of Terminals Optional PartsDimensions