Sanyo PLC-XU106K owner manual Remote Control Operating Range, Remote Control Code

Page 13

Part Names and Functions

Remote Control Battery Installation

1

Open the battery

compartment lid.

2

Install new batteries

3

Replace the

into the compartment.

compartment lid.

Two AAA size batteries

For correct polarity

(+ and –), be sure battery terminals are in contact with pins in compartment.

To ensure safe operation, please observe the following precautions :

Use two (2) AAA or LR03 type alkaline batteries.

Always replace batteries in sets.

Do not use a new battery with a used battery.

Avoid contact with water or liquid.

Do not expose the remote control to moisture or heat.

Do not drop the remote control.

If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

Risk of an explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions or your local disposal rule or guidelines.

Remote Control Operating Range

Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the remote control is about 16.4'(5 m) and 60 degrees in front of the projector.

16.4' (5 m)

30°

30° Remote control

Remote Control Code

The 2 different remote control codes (Code 1-Code 2) are assigned to this projector. Switching the remote control codes prevents interference from other remote controls when several projectors or video equipment next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on page 54.

Press and hold the MENU and IMAGE buttons for more

While pressing the MENU

than five seconds to switch between the Code 1 and Code

button, press the IMAGE

2. The initial code is set to Code 1.

button more than five

 

seconds to switch between

 

the codes.

 

MENU button

 

IMAGE button

13

Image 13
Contents Network Supported Model PLC-XU106 PLC-XU106KFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationPositioning Precautions AC Power Cord for the United States and Canada AC Power Cord RequirementAC Power Cord for the United Kingdom ComplianceFront Part Names and FunctionsBack Bottom⑤ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Remote Control Code Remote Control Operating RangeAdjustable Feet InstallationPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordFor Continental Europe Turning On the Projector Basic OperationSelected Input Source and Lamp Control Basic Operation What is PIN code?Enter a PIN code PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Remote Control Basic Operation How to Operate the On-Screen MenuTop Control On-Screen MenuFor detailed functions of each menu, see Menu Tree on pages Basic Operation Menu BarAuto Setup Function Basic Operation Zoom and Focus AdjustmentStandard Basic Operation Keystone CorrectionCorner Direct Operation Basic Operation Sound AdjustmentMenu Operation Basic Operation Remote Control Operation No Show button Timer buttonImage button Screen buttonInput Source Selection Computer 1 RGB Computer InputInput Menu Computer Input Input Source Selection Computer 2 RGB Selecting Computer System Manually Computer Input Computer System SelectionPC System Menu PC adjust Menu Computer Input Auto PC adjustmentTo store adjustment parameters Auto PC adjComputer Input Manual PC adjustment Reset Mode free MenuMode free Computer InputImage Select Menu Computer Input Image Mode SelectionImage adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentFor zooming in and out the images Digital zoom + CustomDigital zoom Input Source Selection Video, S-video Video InputInput Menu VideoComponent RGB Scart Note AV System Menu Video or S-video Video Input Video System SelectionComponent AV System Menu Component Or Computer 1Component and then pressCinema Video Input Image Mode SelectionImage adjust Menu Video Input Image AdjustmentColor TintVideo Input Off Disabled Lower reduction Higher reduction ProgressiveStore Menu Noise reductionVideo Input Screen Size Adjustment Setting SettingSetting Menu LanguageAuto setup Auto setupInput search Auto KeystoneTimer Power off? p.21Keystone Corner correctionDefault Logo Logo and Logo PIN code lock settings Logo selectLogo PIN code lock CaptureCapture Logo PIN code lockEnter a Logo PIN code Logo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code changePower management Ceiling Rear Power managementCeiling RearOn start Standby modeClosed Caption To change the code for the remote control Remote controlLamp control To change the code for the projectorSecurity Key lock and PIN code lock Key lock PIN code lockKey lock PIN code lockPIN code change Change the PIN code lock settingEnter a PIN code Change the PIN code Fan Fan Control SettingFan control Lamp counterFactory default Factory defaultFilter counter Filter counterInput Source Information Display InformationIndicator is blinking red Maintenance and CleaningIndicator lights red Projector is shut down and the WarningResetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersCleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Service Parts No 333 Maintenance and Cleaning Lamp ReplacementSelect button. Lamp replacement counter Reset? Maintenance and Cleaning Resetting the Lamp CounterAppendix TroubleshootingNo image AppendixNo sound Color is strangeIndicator blinks or lights Remote Control doesImage is distorted or runs off PIN code dialog box appearsAppendix Computer Input/Video Input Appendix Menu TreeSound Computer InputVideo Input SettingIndicators Appendix Indicators and Projector Condition Note Appendix Compatible Computer SpecificationsSignal Compatibility Panel ResolutionPower Mechanical InformationOptional Parts Appendix PJ Link Notice Control Port Connector D-sub 9 pin Appendix Configurations of TerminalsPIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No Unit inchmm Appendix DimensionsKB8AC