Sanyo PLC-XU106K owner manual Input Source Information Display

Page 59

Information

Input Source Information Display

The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.

Direct Operation

Press the INFO. button on the remote control to display the Information Menu.

Menu Operation

Press the Point ▲▼ buttons to select the Information. The Information Menu is displayed.

See below for displayed information.

Input

The selected input source is displayed.

H-sync freq..

The horizontal frequency of the input signal is displayed in KHz, or - - - - - when no signal.

V-sync freq..

The vertical frequency of the input signal is displayed in Hz, or - - - - - when no signal. Numbers of Hz doubles when during Interlace.

Screen

The selected screen size is displayed.

Language

The selected language is displayed.

Lamp status

The selected lamp mode is displayed.

Lamp counter

The cumulative lamp operating time is displayed.

Power management

Off, Ready, Shut down or Timer is displayed.

Key lock

The selected Key lock icon is displayed.

PIN code lock

Off or On 1 or On 2 is displayed.

Remote control

The selected remote code is displayed.

Remote Control

INFO.. button

Information Menu

59

Image 59

Contents Network Supported Model PLC-XU106 PLC-XU106KFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationPositioning Precautions Compliance AC Power Cord RequirementAC Power Cord for the United States and Canada AC Power Cord for the United KingdomBottom Part Names and FunctionsFront Back⑤ LAN Connection Terminal Part Names and Functions Rear TerminalPart Names and Functions Top Control Part Names and Functions Remote Control Remote Control Code Remote Control Operating RangePositioning the Projector InstallationAdjustable Feet Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For Continental Europe Installation Connecting the AC Power CordProjector side AC outlet side Selected Input Source and Lamp Control Basic OperationTurning On the Projector PIN Code Input Dialog Box What is PIN code?Basic Operation Enter a PIN codeBasic Operation Turning Off the Projector On-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlFor detailed functions of each menu, see Menu Tree on pages Basic Operation Menu BarAuto Setup Function Basic Operation Zoom and Focus AdjustmentCorner Basic Operation Keystone CorrectionStandard Menu Operation Basic Operation Sound AdjustmentDirect Operation Basic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonInput Menu Computer InputInput Source Selection Computer 1 RGB Computer Input Input Source Selection Computer 2 RGB PC System Menu Computer Input Computer System SelectionSelecting Computer System Manually Auto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Computer Input Mode free MenuReset Mode freeImage Select Menu Computer Input Image Mode SelectionImage adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentDigital zoom CustomFor zooming in and out the images Digital zoom + Video Video InputInput Source Selection Video, S-video Input MenuComponent RGB Scart Note Or Computer 1Component and then press Video Input Video System SelectionAV System Menu Video or S-video Component AV System Menu ComponentCinema Video Input Image Mode SelectionTint Video Input Image AdjustmentImage adjust Menu ColorNoise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Store MenuVideo Input Screen Size Adjustment Language SettingSetting Setting MenuAuto Keystone Auto setupAuto setup Input searchCorner correction Power off? p.21Timer KeystoneDefault Logo Logo and Logo PIN code lock settings Logo selectLogo PIN code lock CaptureLogo PIN code lock CaptureLogo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code change Enter a Logo PIN codeRear Ceiling Rear Power managementPower management CeilingClosed Caption Standby modeOn start To change the code for the projector Remote controlTo change the code for the remote control Lamp controlPIN code lock Key lock PIN code lockSecurity Key lock and PIN code lock Key lockEnter a PIN code Change the PIN code Change the PIN code lock settingPIN code change Lamp counter Fan Control SettingFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationProjector is shut down and the Warning Maintenance and CleaningIndicator is blinking red Indicator lights redResetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersCleaning the Projector Cabinet Maintenance and Cleaning Attaching the Lens CapCleaning the Projection Lens Service Parts No 333 Maintenance and Cleaning Lamp ReplacementSelect button. Lamp replacement counter Reset? Maintenance and Cleaning Resetting the Lamp CounterAppendix TroubleshootingColor is strange AppendixNo image No soundPIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Computer Input Appendix Menu TreeComputer Input/Video Input SoundVideo Input SettingIndicators Appendix Indicators and Projector Condition Note Appendix Compatible Computer SpecificationsMechanical Information Panel ResolutionSignal Compatibility PowerOptional Parts Appendix PJ Link Notice Control Port Connector D-sub 9 pin Appendix Configurations of TerminalsLogo PIN Code Lock No Appendix PIN Code Number MemoPIN Code Lock No Unit inchmm Appendix DimensionsKB8AC