Sanyo PLC-XE50 owner manual How to Use the Antitheft Alarm Function, Indicator

Page 53

Antitheft Alarm Function

How to Use the Antitheft Alarm Function

Antitheft alarm function is provided to prevent the projector from being stolen. When this function is set to “On,” the alarm rings as an unauthorized person tries to move the projector.

To activate the Alarm function for the first time after purchase, you must turn on the power once.

Note:

•This function is not a guarantee against stealing.

•The alarm does not ring while the AC power cord is connected to an outlet even if the projector detects vibrations.

•The alarm will stop, as the AC power cord is connected to an outlet, except when the battery cover is open. •Pressing the buttons is always accompanied by a sound. If no sound is produced after pressing a button, you need to press it again.

The Alarm function is operated by a built-in rechargeable battery. The alarm will not work properly if the battery is not charged enough. See page 55 for details.

Set and release the Antitheft alarm function

The Alarm setting and release and PIN Code change can be made without an AC power connection.

Set the alarm

Indicator

Press the F button three times to turn the alarm function on. The ALARM indicator blinks for a few seconds and the projector enters the warning mode. (If the battery is not charged enough for the alarm function to operate normally, it bleeps and the Alarm indicator will blink red every 20 seconds.)

During the Antitheft alarm function is on, the projector emits a low-pitched sound when it detects vibration.

When the projector does not detect vibration for a few seconds after the sound, it goes back to the warning mode. When the projector detects more vibrations after the low- pitched sound, the alarm starts ringing.

The Alarm operating configuration (Battery charge, Alarm volume, Sensitivity, and Ringing time) can be selected in the menu. See page 54.

Note:

•You can test the alarm sound without setting the alarm function. Press and hold the F button, then the alarm starts ringing. The duration of the alarm sound is the same as the “Ringing Time” setting (p.54).

•If you want to stop the alarm while it is ringing, insert the AC power cord to an outlet or press the F button and enter the four-digit PIN code number.

Release the alarm setting

Press the F button and enter the four-digit PIN code number within about 10 seconds. (The default PIN code is set to “1111.”) When the alarm is released, you will hear a high- pitched confirmation sound.

When you enter an incorrect PIN code, you will hear a low- pitched sound. If you enter an incorrect PIN code three times in a row, the alarm will start ringing.

ALARM indicator

Terminal

Button 1, 2, 3 F button

53

Image 53
Contents Model PLC-XE50 Large Screen in Limited Space Features and DesignTable of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationSide a Side B Federal Communications Commission Notice CompliancePart Names and Functions Indicators Infrared Remote ReceiverFront Back Bottom Exhaust VentPart Names and Functions Rear Terminal Alarm indicator Part Names and Functions IndicatorsPower indicator Lamp Replace indicatorPart Names and Functions Remote Control Operating Range Part Names and Functions Remote Control Battery InstallationPositioning the Projector InstallationCables used for connection Installation Connecting to ComputerInstallation Connecting to Video Equipment VIdeo, S-Video Component Audio Computer Projector side AC outlet side Installation Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the Projector On-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Menu button Point buttons Select button For computer source Basic Operation Menu BarKeystone Correction Basic Operation Focus AdjustmentRemote Control Remote Control Operation Basic Operation Sound AdjustmentCOMPUTER/VIDEO button Freeze buttonBasic Operation Input Source Selection Computer InputInput Menu Source Select MenuAuto Computer Input Computer System SelectionPC System Menu ModeDirect Operation Remote Control Computer Input Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Image Select Menu BlackboardGreenComputer Input Image Level Adjustment Screen Size Adjustment Custom For zooming in and out the imagesDigital zoom + Digital zoomVideo Input Menu Operation Remote ControlInput Source Selection Video, S-Video, Component Auto Video ComponentRGB Scart Video Input Input Source Selection RGB Scart 21-pinVideo or S-Video Auto Video Input Video System SelectionComponent Auto AV System Menu Video or S-VideoCinema Video Input Image Level SelectionImage1-4 Video InputTint Video Input Image Level AdjustmentColor Progressive Noise reductionVideo Input Screen Size Adjustment Setting SettingLanguage Setting Menu Language KeystoneDisplay Blue backLogo select Logo Logo and Logo PIN code lock settingsCapture Logo select CaptureLogo PIN code lock Enter a Logo PIN codeChange the Logo PIN code Rear CeilingTerminal Input searchLamp control Power managementOn start PIN code lock Security Alarm and PIN code lock settingTo change the code for the projector Change the PIN code lock setting Change the PIN code lock settingChange the PIN code Enter a PIN codeLamp Replacement icon Factory defaultFan Lamp counterHow to Use the Antitheft Alarm Function Antitheft Alarm FunctionSet and release the Antitheft alarm function IndicatorOther settings Antitheft Alarm FunctionReplace the rechargeable batteries How to replace the rechargeable batteriesCharge the built-in batteries SAFETY Precautions for Sanyo Ni-MH Battery Pack Then check the matters below Maintenance and CleaningIndicators Page Cleaning the Projector Cabinet Maintenance and Cleaning Cleaning the Projection WindowService Parts No 337 Maintenance and Cleaning Lamp ReplacementReset the lamp counter Maintenance and Cleaning Lamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingImage is out of focus AppendixAppears on the screen Remote Control does not workComputer Input Menu TreeComputer Input/Video Input Image Adjust Screen SettingProjector Condition Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsTechnical Specifications Optional Parts AccessoriesDimensions Appendix Configurations of TerminalsService Port Connector Terminal Mini DIN 8-PIN Terminal Analog RGB Mini D-sub 15 pinAppendix PIN Code Number Memo Lamp Replacement LabelKL3A