Sanyo PLC-WL2500 owner manual Video Input, Input Source Selection Video, S-video, Video Note

Page 37

Video Input

Input Source Selection (Video, S-video)

Direct Operation

Choose Video or S-videoby pressing the VIDEO button or the S-VIDEO button on the remote control or press the INPUT button on the top control.

Before using these buttons, correct input source should be selected through Menu operation as described below.

Remote Control

VIDEO button

Video

S-VIDEO button S-video

Top Control

INPUT button

Computer 1

Computer 2 *

HDMI

Video

S-video

*COMPUTER 2 can not be selected when using the COMPUTER IN 2/ MONITOR OUT terminal as MONITOR OUT output.

Menu Operation

Input Menu

1	Press the MENU button to display the On-Screen
	Menu. Use the Point ▲▼ buttons to select Input and
2	then press the Point ► or the SELECT button.
	Use the Point	▲▼	buttons to select either Video or

S-videoand then press the SELECT button.

Video

S-video

Note:

When video input signal is connected to the VIDEO jack, select Video.

When video input signal is connected to the S- VIDEO jack, select S-video.

When the Input Search function is set to On 1 or On 2 in the Auto setup function, the input signal will be searched automatically (p.45).

37

Image 37

Contents Network Supported Model PLC-WL2500Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Side Part Names and Functions⑧ Exhaust vent  Kensington Security Slot① LAN Connection Terminal Part Names and Functions Side TerminalPart Names and Functions Top Panel Part Names and Functions Remote Control Remote Control Code Remote Control Operating RangeTwo AAA size batteries Menu buttonAdjustable Feet InstallationPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Projector side AC outlet side Installation Connecting the AC Power CordFor Continental Europe For the U..K For the U..S..A.. and CanadaBasic Operation Input signal guidance windowTurning On the Projector Selected Input Source and Lamp ControlPIN Code Input Dialog Box Basic OperationDirect OFF Function Basic Operation Turning Off the ProjectorRemote Control Basic Operation How to Operate the On-Screen MenuTop Control On-Screen MenuBasic Operation Menu Bar Auto Setup Function Basic Operation Focus AdjustmentKeystone Correction Volume Basic Operation Sound AdjustmentVolume Dialog Box MuteBasic Operation Remote Control Operation No Show button Timer buttonImage button Screen buttonInput Source Selection Computer 1 RGB Computer InputInput Menu Input Menu Computer Input Input Source Selection Computer 2 RGBComputer 2 button Computer 2 RGB VideoPC System Menu Computer Input Computer System SelectionAuto ModePC adjust Menu Computer Input Auto PC adjustmentTo store adjustment parameters Auto PC adjComputer Input Manual PC adjustment Computer Input Mode free MenuStore Menu Computer Input Image Mode Selection Image adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentDigital zoom + Custom adjDigital zoom Custom adj.. Menu NoteInput Source Selection Video, S-video Video InputVideo Note Video button Video button S-videoComputer 1 Scart Computer 1 RGBHdmi button Component buttonAV System Menu Video or S-video Video Input Video System SelectionAV System Menu Component Or Computer 1Component and then pressVideo Input Image Mode Selection Image adjust Menu Video Input Image AdjustmentColor TintVideo Input Off Disabled Lower reduction Higher reduction ProgressiveNoise reduction Zoom Video Input Screen Size AdjustmentWide Natural wideSetting SettingSetting Menu Language Menu LanguageAuto setup Auto setupInput search Power off? p.20 Store or ResetTimer KeystoneDefault Logo Logo and Logo PIN code lock settingsLogo select Logo selectCapture Capture Logo PIN code lockOff Logo PIN code lock Enter a Logo PIN code Logo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code changeCeiling Rear Hdmi setupStandby mode Power managementPower management Direct on Min . Only set to Count down , Timer isNote Count downOff , CC1 , CC2 , CC3 or CC4 Closed captionFrom Color to White Note Lamp control Remote controlTo change the code for the projector Security Key lock and PIN code lock Enter a PIN code Change the PIN code Fan Video delay controlFan control Lamp counterFactory default Factory defaultFilter counter Filter counterInput Source Information Display InformationProjector is shut down and the Warning indicator lights red Maintenance and CleaningNote Then check the matters below Resetting the Filter Counter Maintenance and Cleaning Replacing the FilterFilter counter Reset? Cleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CoverCleaning the Projector Cabinet Reset the lamp counter Maintenance and Cleaning Lamp ReplacementService Parts No 349 Top PanelPress Select button. Lamp replacement counter Maintenance and Cleaning Resetting the Lamp CounterLamp replacement counter Reset? appears Appendix TroubleshootingAppendix Indicator blinks or lights Remote Control doesImage is distorted or runs off PIN code dialog box appearsAppendix Menu Tree Information SettingIndicators Appendix Indicators and Projector Condition Note Appendix Compatible Computer SpecificationsFreq Technical Specifications Appendix Optional Parts Terminal Panel ReplacementControl Port Connector D-sub 9 pin Appendix Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Hdmi 19 PIN Type aPIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No PJ Link Notice Appendix DimensionsKJ8AD