Sanyo PLC-WL2500 owner manual Safety Instructions Air Circulation, Moving the Projector

Page 6

Safety Instructions

Air Circulation

Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

CAUTION

Hot air is exhausted from the exhaust vent. When using or installing the projector, the following precautions should be taken.

Do not put any flammable object or spray can near the projector, hot air is exhausted from the air vents.

Keep the exhaust vent at least 3’ (1 m) away from any objects.

Do not touch a peripheral part of the exhaust vent, especially screws and metallic parts. These areas will become hot while the projector is being used.

Do not put anything on the cabinet. Objects put on the cabinet will not only get damaged but also may cause fire hazard by heat.

Cooling fans are provided to cool down the projector. The fans’ running speed is changed according to the temperature inside the projector.

Air Intake Vent

Exhaust Vent

(Hot air exhaust)

Do not point the projector up to project an image.

Do not point the projector down to project an image.

Do not put the projector on either side to project an image.

CAUTION

Choose the running speed of cooling fans in the fan control setting according to the altitude in which the projector is being used (p.57). Failure to do so may affect the projector life.

CAUTION ON CEILING MOUNTING

For ceiling mounting, you need the ceiling mount kit designed for this projector. When not mounted properly, the projector may fall, causing hazards or injury. For details, consult your dealer. The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

Moving the Projector

When moving the projector, replace the lens cover and retract adjustable feet to prevent damage to the lens and cabinet. When the projector is not in use for an extended period, put it into a suitable case. Handle the projector carefully; do not drop, bump, subject it to strong forces, or put other things on the cabinet.

Exhaust Vent (Hot air exhaust)

Air Intake Vent

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

–  Do not drop or bump the projector, otherwise damages or malfunctions may result.

Installing the Projector in Proper Position

Install the projector properly. Improper installation may reduce the lamp life and cause fire hazard.

Do not roll the projector more than 20 degrees from side to side.

(

Do not pitch the projector more

 

than 20 degrees backward and

 

 

 

forward.

–  When carrying the projector, use a suitable case. –  Do not transport the projector by courier or any other transport service in an unsuitable transport case. This may cause damage to the projector.

For information about transporting the projector by courier or any other transport service, consult your dealer.

–  Do not put the projector in a case before it is cooled enough.

Image 6
Contents Model PLC-WL2500 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance ⑧ Exhaust vent Part Names and FunctionsFront Side  Kensington Security SlotPart Names and Functions Side Terminal ① LAN Connection TerminalPart Names and Functions Top Panel Part Names and Functions Remote Control Two AAA size batteries Remote Control Operating RangeRemote Control Code Menu buttonInstallation Adjustable FeetPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For Continental Europe For the U..K Installation Connecting the AC Power CordProjector side AC outlet side For the U..S..A.. and CanadaTurning On the Projector Input signal guidance windowBasic Operation Selected Input Source and Lamp ControlBasic Operation PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Direct OFF FunctionTop Control Basic Operation How to Operate the On-Screen MenuRemote Control On-Screen MenuBasic Operation Menu Bar Basic Operation Focus Adjustment Auto Setup FunctionKeystone Correction Volume Dialog Box Basic Operation Sound AdjustmentVolume MuteBasic Operation Remote Control Operation Image button Timer buttonNo Show button Screen buttonComputer Input Input Source Selection Computer 1 RGBInput Menu Computer 2 button Computer 2 RGB Computer Input Input Source Selection Computer 2 RGBInput Menu VideoAuto Computer Input Computer System SelectionPC System Menu ModeTo store adjustment parameters Computer Input Auto PC adjustmentPC adjust Menu Auto PC adjComputer Input Manual PC adjustment Mode free Menu Computer InputStore Menu Computer Input Image Mode Selection Computer Input Image Adjustment Image adjust MenuScreen Size Adjustment Screen MenuDigital zoom Custom adjDigital zoom + Custom adj.. Menu NoteVideo Note Video InputInput Source Selection Video, S-video Video button Video button S-videoHdmi button Computer 1 RGBComputer 1 Scart Component buttonAV System Menu Component Video Input Video System SelectionAV System Menu Video or S-video Or Computer 1Component and then pressVideo Input Image Mode Selection Color Video Input Image AdjustmentImage adjust Menu TintOff Disabled Lower reduction Higher reduction Progressive Video InputNoise reduction Wide Video Input Screen Size AdjustmentZoom Natural wideSetting Menu Language Menu SettingSetting LanguageAuto setup Auto setupInput search Timer Store or ResetPower off? p.20 KeystoneLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectCapture Logo PIN code lock CaptureOff Logo PIN code lock Enter a Logo PIN code Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code change Logo PIN code changeHdmi setup Ceiling RearPower management Standby modePower management Note Min . Only set to Count down , Timer isDirect on Count downClosed caption Off , CC1 , CC2 , CC3 or CC4From Color to White Note Remote control Lamp controlTo change the code for the projector Security Key lock and PIN code lock Enter a PIN code Change the PIN code Fan control Video delay controlFan Lamp counterFilter counter Factory defaultFactory default Filter counterInformation Input Source Information DisplayMaintenance and Cleaning Projector is shut down and the Warning indicator lights redNote Then check the matters below Maintenance and Cleaning Replacing the Filter Resetting the Filter CounterFilter counter Reset? Maintenance and Cleaning Attaching the Lens Cover Cleaning the Projection LensCleaning the Projector Cabinet Service Parts No 349 Maintenance and Cleaning Lamp ReplacementReset the lamp counter Top PanelMaintenance and Cleaning Resetting the Lamp Counter Press Select button. Lamp replacement counterLamp replacement counter Reset? appears Troubleshooting AppendixAppendix Image is distorted or runs off Remote Control doesIndicator blinks or lights PIN code dialog box appearsAppendix Menu Tree Setting InformationAppendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications  NoteFreq Technical Specifications Terminal Panel Replacement Appendix Optional PartsTerminal Analog RGB Mini D-sub 15 pin Appendix Configurations of TerminalsControl Port Connector D-sub 9 pin Hdmi 19 PIN Type aAppendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Appendix Dimensions PJ Link NoticeKJ8AD