Sanyo PLC-WL2500 Image is distorted or runs off, PIN code dialog box appears, At start-up

Page 67

 

 

Appendix

 

 

 

 

 

 

 

 

 

The image is distorted or runs off.

– Check PC adjustment Menu or Screen and adjust them.

 

 

See pages 31-32, 35-36.

 

 

 

 

 

PIN code dialog box appears

– PIN code lock is being set. Enter a PIN code (the “1234” or numbers

 

at start-up..

you have set). See pages 19, 55-56.

 

 

 

 

 

The Remote Control does

– Check the batteries.

 

not work..

– Make sure no obstruction is between the projector and remote

 

 

control.

 

 

– Make sure you are not too far from the projector when using the

 

 

remote control. Maximum operating range is 16.4'(5 m).

 

 

– Make sure the code of the remote control is conformed to the

 

 

projector’s code. See page 54.

 

 

– Unlock the Key lock function for the remote control function.

 

 

See page 55.

 

 

 

 

 

Indicator blinks or lights.

– Check the status of the projector with referring to "Indicators and

 

 

projector Condition". See page 70.

 

 

 

 

 

The exclamation mark appears

– Your operation is invalid. Operate correctly.

 

on the screen..

 

 

Top control does not work..

The top control is not available if the top control is locked at Key lock under Security of SETTING section. See page 54.

Unable to unlock the Logo PIN code lock or Security PIN code lock..

Contact the dealer where you purchased the projector or the service center.

WARNING :

High voltages are used to operate this projector.. Do not attempt to open the cabinet..

If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service.

The CE Mark is a Directive conformity mark of the European Community (EC).

Licensed under USP5,717,422 USP6,816,141 USP7,352,347

Pixelworks ICs used.

This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.

67

Image 67
Contents Network Supported Model PLC-WL2500Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance  Kensington Security Slot Part Names and FunctionsFront Side ⑧ Exhaust vent① LAN Connection Terminal Part Names and Functions Side TerminalPart Names and Functions Top Panel Part Names and Functions Remote Control Menu button Remote Control Operating RangeRemote Control Code Two AAA size batteriesAdjustable Feet InstallationPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For the U..S..A.. and Canada Installation Connecting the AC Power CordProjector side AC outlet side For Continental Europe For the U..KSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationDirect OFF Function Basic Operation Turning Off the ProjectorOn-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlBasic Operation Menu Bar Auto Setup Function Basic Operation Focus AdjustmentKeystone Correction Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonInput Source Selection Computer 1 RGB Computer InputInput Menu Video Computer Input Input Source Selection Computer 2 RGBInput Menu Computer 2 button Computer 2 RGBMode Computer Input Computer System SelectionPC System Menu AutoAuto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Computer Input Mode free MenuStore Menu Computer Input Image Mode Selection Image adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentCustom adj.. Menu Note Custom adjDigital zoom + Digital zoomVideo button Video button S-video Video InputInput Source Selection Video, S-video Video NoteComponent button Computer 1 RGBComputer 1 Scart Hdmi buttonOr Computer 1Component and then press Video Input Video System SelectionAV System Menu Video or S-video AV System Menu ComponentVideo Input Image Mode Selection Tint Video Input Image AdjustmentImage adjust Menu ColorVideo Input Off Disabled Lower reduction Higher reduction ProgressiveNoise reduction Natural wide Video Input Screen Size AdjustmentZoom WideLanguage SettingSetting Setting Menu Language MenuAuto setup Auto setupInput search Keystone Store or ResetPower off? p.20 TimerLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectCapture Capture Logo PIN code lockOff Logo PIN code lock Logo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code change Enter a Logo PIN codeCeiling Rear Hdmi setupStandby mode Power managementPower management Count down Min . Only set to Count down , Timer isDirect on NoteOff , CC1 , CC2 , CC3 or CC4 Closed captionFrom Color to White Note Lamp control Remote controlTo change the code for the projector Security Key lock and PIN code lock Enter a PIN code Change the PIN code Lamp counter Video delay controlFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationProjector is shut down and the Warning indicator lights red Maintenance and CleaningNote Then check the matters below Resetting the Filter Counter Maintenance and Cleaning Replacing the FilterFilter counter Reset? Cleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CoverCleaning the Projector Cabinet Top Panel Maintenance and Cleaning Lamp ReplacementReset the lamp counter Service Parts No 349Press Select button. Lamp replacement counter Maintenance and Cleaning Resetting the Lamp CounterLamp replacement counter Reset? appears Appendix TroubleshootingAppendix PIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Menu Tree Information SettingIndicators Appendix Indicators and Projector Condition Note Appendix Compatible Computer SpecificationsFreq Technical Specifications Appendix Optional Parts Terminal Panel ReplacementHdmi 19 PIN Type a Appendix Configurations of TerminalsControl Port Connector D-sub 9 pin Terminal Analog RGB Mini D-sub 15 pinPIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No PJ Link Notice Appendix DimensionsKJ8AD