Sanyo PDG-DHT8000L owner manual Then check the matters below

Page 72

Maintenance and Care

Warning Indicators

The WARNING indicators show the state of the function which protects the projector. Check the state of the WARNING TEMP. indicator and the LAMP indicator to take proper maintenance.

The projector is shut down and the WARNING TEMP. indicator is blinking red.

When the temperature inside the projector reaches a certain level, the projector will be automatically shut down to protect the inside of the projector. The LAMP indicator turns red brighter and the WARNING TEMP indicator blinks while the projector is being cooled down. When the projector has cooled down enough (to its normal operating temperature), it can be turned on again by pressing the ON/ STAND-BY button.

✔Note:

•The WARNING TEMP. indicator continues to blink even after the temperature inside the projector returns to normal. When the projector is turned on again, the WARNING TEMP. indicator stops blinking.

Indicators

WARNING TEMP.. blinking red

Then check the matters below:

–Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if the air vents of the projector are not blocked.

–Has the projector been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent.

–Is the filter clean? Replace the filter with a new one.

The projector is shut down; and the LAMP indicator is lighting and other indicators are blinking.

When the projector detects an abnormal condition, it will be automatically shut down to protect the inside of the projector and the LAMP indicator lights on and other indicators blink. In this case, unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the projector cannot be turned on and these indicators are still lighting and blinking, unplug the AC power cord and contact the service center.

CAUTION

DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK.

Indicators

LAMP indicator lights on and other indicators blink..

72

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Model PDG-DHT8000L Features and Design Table of Contents To The Owner For EU UsersSafety Instructions Air Circulation Top PanelInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector AC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Canadian Radio Interference RegulationsPart Names and Functions Front!0Back Terminals and Connectors Side Control and Indicators Side ControlIndicators Remote Control Remote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Code Installation Lens InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment When the lens is shifted to topWhen the lens is shifted to bottom Replacement of Terminal Terminals of ProjectorConnecting to Computer Cables used for connectionTerminals of the projector Connecting to Video Equipment Monitor Out Signal TableProjector Attaching the Cable Tie To loosen the cable tieConnecting the AC Power Cord For the U..KFor the U..S..A.. and Canada For Continental Europe What is PIN code? Basic OperationTurning On the Projector Enter a PIN codeUnplug the AC power cord from the AC outlet Turning Off the ProjectorHow to Operate the On-Screen Menu Remote ControlSide Control On-Screen MenuMenu Bar Operating with Projector Control Information Operating with Remote Control Timer button Shutter buttonFilter button Image ADJ.. buttonRemote Control Operation Input SelectionInput Side Control OperationWhen Selecting the Input 1 with DVI/D-sub 15 terminals Computer Input Source SelectionMenu Operation Input MenuVideo Input Source Selection RGB ScartRGB AV Hdcp Pb/Cb, Pr/CrComputer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyAuto PC Adjustment To store the adjusted parametersPC Adjust Menu Direct OperationManual PC Adjustment Reset Mode freeTo clear the adjusted data To store the adjusted dataImage Level Selection Standard Real Dynamic Image1 Image SEL.. buttonStandard ImageScreen Size Adjustment Screen MenuKeystone CeilingRear Digital zoom +Video Input Video System SelectionVideo Jack or S-Video Jack Pb/Cb, Pr/Cr JacksStandard Cinema Dynamic Image1 Image SEL.. button Natural Wide Keystone Image Adjustment Image Adjust MenuPointer Mode Picture ImageColor M MenuColor Palette DELWhite balance Red/Green/Blue Offset Red/Green/BlueSharpness GammaSetting SettingLamp mode BackgroundLamp control Lamp life controlPicture in Picture Edge blending Color matchingDynamicBlack Advanced color matchingHdmi setup LogoLogo select CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Remote control To change the code for the remote controlTo reset the code for the remote control Filter controlPower management On startSecurity Key lock PIN code lockSecurity Key lock PIN code lockChange the PIN Code Lock setting Change the PIN code lock settingChange the PIN Code Enter a PIN codeShutter ProtectionEffect Release keyVideo delay control Closed captionFrame lock Filter counter  Last scroll iconFactory default Test patternMaintenance and Care Filter InstructionsReset the filter counter and the scroll counter p.66 Service Parts Code 610 350Replacing the Filter Cartridge Filter counter Scroll counterLamp 1/2 Replace Indicators Lamp Mode ChangeoverLamp Management Lamp Status DisplayLamp Replacement IndicatorsLamp 1 / 2 Replace indicators Replacement Lamp Type No Model No.. of your projectorOptional Color Wheel Installation Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Power is turned off Information Image Adjust Menu TreeComputer Input/Video Input NetworkPC Adjust SystemImage Select ScreenEdge blending Languages provided. Quit Indicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition Lamp Replace 1If the Filter counter reached a time set in the timer Compatible Computer Specifications ON-SCREEN ResolutionFreq..kHz Freq..Hz Display30.000 Supported Signal Format for Optional Board List of Picture in PictureTechnical Specifications Optional Parts POA-AMD17SDIDConfigurations of Terminals InputOutput PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Dimensions Unit inch mmFunctional Execution Command Serial Control InterfaceOperation ExampleStatus Read Command How to adjust multiple screens Edge blendingColor matching Fig..1 For rich color reproduction color wheelKE2AL

PDG-DHT8000L specifications

The Sanyo PDG-DHT8000L is a high-performance projector designed for a variety of professional environments, offering outstanding image quality, advanced technologies, and versatile connectivity options. Ideal for corporate presentations, educational settings, and large venue applications, this projector stands out for its combination of robust features and user-friendly design.

At the heart of the PDG-DHT8000L is its advanced DLP (Digital Light Processing) technology. This ensures exceptional image clarity and brightness, with a remarkable resolution of 1920 x 1080 pixels, allowing for brilliant Full HD visuals. The projector achieves a brightness level of up to 8000 ANSI lumens, making it suitable for use in well-lit environments without sacrificing image quality. This high brightness is complemented by a high contrast ratio that enhances the depth and detail in images, ensuring that presentations are impactful and engaging.

Another significant feature of the PDG-DHT8000L is its comprehensive lens options. The projector supports interchangeable lenses, which provide flexibility in installation and allows users to choose the ideal lens to match their specific projection needs. This capability makes it easy to adapt the projector to various room sizes and layouts, ensuring optimal performance in any setting.

The PDG-DHT8000L also incorporates advanced color technology, including a color wheel that enhances color reproduction. This results in rich, vibrant colors that create an immersive viewing experience. Additionally, the projector features various color adjustment settings, making it easier for users to calibrate the device according to their preferences or specific lighting conditions.

In terms of connectivity, the Sanyo PDG-DHT8000L excels with multiple input options, including HDMI, RGB, and composite video, enabling seamless integration with various devices such as laptops, Blu-ray players, and gaming consoles. The projector also supports network connectivity, allowing for easy remote control and management over a LAN connection, which is particularly useful in corporate and educational environments.

With a robust build quality and reliable performance, the Sanyo PDG-DHT8000L is designed for longevity and ease of use. Its user-friendly interface and intuitive control features make operation straightforward, while its robust cooling system ensures efficient performance even during long presentations. Overall, the Sanyo PDG-DHT8000L is a powerful tool that delivers exceptional visual quality and versatility, making it an excellent choice for professionals seeking a reliable projection solution.
Top Page Image Contents