Sanyo PDG-DHT8000L owner manual Power is turned off

Page 75

Appendix

The power is turned off

– Power management function runs by initial setting. Check “SETTING” section on page

automatically.

57.

 

 

You cannot operate with

– The side control is not available If the side control is locked at “Key lock” under

the side control.

“Security” of SETTING section. Please check “SETTING” section on page 58.

 

 

 

– Check the batteries.

 

– Check if the RC sensor is set properly. (See page 56)

 

– Make sure no obstruction is between the projector and remote control.

 

– Make sure you are not too far from the projector when using the remote control.

The Remote Control does

Maximum operating range is 16.4’ (5m).

– Make sure that the remote control code conforms to the projector’s code.

not work.

(See “SETTING” section on page 56.)

 

– Make sure the reset switch in the compartment lid on back of the remote control is set

 

to use position.

 

– Unlock the Key lock function for the remote control. (See page 58)

 

– Wireless remote control does not work when the remote control cable is connected to

 

the projector. (See page 15)

Indicators blinks or lights.

– Check the status of the projector with referring to “ INDICATORS AND PROJECTOR

 

CONDITION” on pages 79-81.

 

 

 

– Your operation is invalid. Operate correctly.

appears on the screen

 

 

 

Unable to unlock the Logo

 

PIN code lock, Security

– Contact the dealer where you purchased the projector or the service center.

key lock or Security PIN

 

code lock.

 

 

 

Forget the Logo PIN code

– Contact the dealer where you purchased the projector or the service center.

or Security PIN code.

 

 

 

WARNING:

High voltages are used to operate this projector.. Do not attempt to open the cabinet..

If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service.

This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty, and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Pixelworks ICs used.

75

Page 74 Page 76
Image 75
Page 74 Page 76
Contents Model PDG-DHT8000L Features and Design Table of Contents For EU Users To The OwnerSafety Instructions Top Panel Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsMoving the Projector Canadian Radio Interference Regulations AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom CompliancePart Names and Functions Front!0Back Terminals and Connectors Side Control Side Control and IndicatorsIndicators Remote Control Remote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Code Positioning Projector InstallationLens Installation Picture Level and Pitch AdjustmentLens Shift Adjustment When the lens is shifted to topWhen the lens is shifted to bottom Terminals of Projector Replacement of TerminalConnecting to Computer Cables used for connectionTerminals of the projector Connecting to Video Equipment Monitor Out Signal TableProjector To loosen the cable tie Attaching the Cable TieConnecting the AC Power Cord For the U..KFor the U..S..A.. and Canada For Continental Europe Enter a PIN code What is PIN code?Basic Operation Turning On the ProjectorTurning Off the Projector Unplug the AC power cord from the AC outletOn-Screen Menu How to Operate the On-Screen MenuRemote Control Side ControlMenu Bar Operating with Projector Control Information Operating with Remote Control Image ADJ.. button Timer buttonShutter button Filter buttonSide Control Operation Remote Control OperationInput Selection InputInput Menu When Selecting the Input 1 with DVI/D-sub 15 terminalsComputer Input Source Selection Menu OperationPb/Cb, Pr/Cr Video Input Source SelectionRGB Scart RGB AV HdcpSelecting Computer System Manually Computer InputComputer System Selection Automatic Multi-Scan SystemDirect Operation Auto PC AdjustmentTo store the adjusted parameters PC Adjust MenuManual PC Adjustment To store the adjusted data ResetMode free To clear the adjusted dataImage Image Level SelectionStandard Real Dynamic Image1 Image SEL.. button StandardScreen Menu Screen Size AdjustmentDigital zoom + KeystoneCeiling RearPb/Cb, Pr/Cr Jacks Video InputVideo System Selection Video Jack or S-Video JackStandard Cinema Dynamic Image1 Image SEL.. button Natural Wide Keystone Picture Image Image AdjustmentImage Adjust Menu Pointer ModeDEL Color MMenu Color PaletteGamma White balance Red/Green/BlueOffset Red/Green/Blue SharpnessSetting SettingLamp life control Lamp modeBackground Lamp controlPicture in Picture Color matching Edge blendingAdvanced color matching DynamicBlackCapture Hdmi setupLogo Logo selectChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Filter control Remote controlTo change the code for the remote control To reset the code for the remote controlOn start Power managementKey lock PIN code lock Security Key lockPIN code lock SecurityEnter a PIN code Change the PIN Code Lock settingChange the PIN code lock setting Change the PIN CodeRelease key ShutterProtection EffectVideo delay control Closed captionFrame lock  Last scroll icon Filter counterTest pattern Factory defaultFilter Instructions Maintenance and CareReset the filter counter and the scroll counter p.66 Service Parts Code 610 350Replacing the Filter Cartridge Scroll counter Filter counterLamp Status Display Lamp 1/2 Replace IndicatorsLamp Mode Changeover Lamp ManagementLamp Replacement IndicatorsLamp 1 / 2 Replace indicators Model No.. of your projector Replacement Lamp Type NoOptional Color Wheel Installation Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingAppendix Power is turned off Network Information Image AdjustMenu Tree Computer Input/Video InputScreen PC AdjustSystem Image SelectEdge blending Languages provided. Quit Projector is operating normally Indicators and Projector ConditionLamp Replace 1 Projector is detecting abnormal conditionIf the Filter counter reached a time set in the timer Display Compatible Computer SpecificationsON-SCREEN Resolution Freq..kHz Freq..Hz30.000 List of Picture in Picture Supported Signal Format for Optional BoardTechnical Specifications POA-AMD17SDID Optional PartsConfigurations of Terminals InputOutput PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Unit inch mm DimensionsExample Functional Execution CommandSerial Control Interface OperationStatus Read Command Edge blending How to adjust multiple screensFig..1 For rich color reproduction color wheel Color matchingKE2AL

PDG-DHT8000L specifications

The Sanyo PDG-DHT8000L is a high-performance projector designed for a variety of professional environments, offering outstanding image quality, advanced technologies, and versatile connectivity options. Ideal for corporate presentations, educational settings, and large venue applications, this projector stands out for its combination of robust features and user-friendly design.

At the heart of the PDG-DHT8000L is its advanced DLP (Digital Light Processing) technology. This ensures exceptional image clarity and brightness, with a remarkable resolution of 1920 x 1080 pixels, allowing for brilliant Full HD visuals. The projector achieves a brightness level of up to 8000 ANSI lumens, making it suitable for use in well-lit environments without sacrificing image quality. This high brightness is complemented by a high contrast ratio that enhances the depth and detail in images, ensuring that presentations are impactful and engaging.

Another significant feature of the PDG-DHT8000L is its comprehensive lens options. The projector supports interchangeable lenses, which provide flexibility in installation and allows users to choose the ideal lens to match their specific projection needs. This capability makes it easy to adapt the projector to various room sizes and layouts, ensuring optimal performance in any setting.

The PDG-DHT8000L also incorporates advanced color technology, including a color wheel that enhances color reproduction. This results in rich, vibrant colors that create an immersive viewing experience. Additionally, the projector features various color adjustment settings, making it easier for users to calibrate the device according to their preferences or specific lighting conditions.

In terms of connectivity, the Sanyo PDG-DHT8000L excels with multiple input options, including HDMI, RGB, and composite video, enabling seamless integration with various devices such as laptops, Blu-ray players, and gaming consoles. The projector also supports network connectivity, allowing for easy remote control and management over a LAN connection, which is particularly useful in corporate and educational environments.

With a robust build quality and reliable performance, the Sanyo PDG-DHT8000L is designed for longevity and ease of use. Its user-friendly interface and intuitive control features make operation straightforward, while its robust cooling system ensures efficient performance even during long presentations. Overall, the Sanyo PDG-DHT8000L is a powerful tool that delivers exceptional visual quality and versatility, making it an excellent choice for professionals seeking a reliable projection solution.
Top Page Image Contents