Hitachi CP-X255 user manual Setup Menu, Volume, Audio

Page 34

Multifunctional settings

SETUP Menu

With the SETUP menu, the items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table.

 MENU [RGB]

   :SELECT

 PICTURE

 KEYSTONE     +0

 IMAGE

 WHISPER      NORMAL

 INPUT

 MIRROR       NORMAL

 SETUP

 VOLUME       16

 SCREEN

 AUDIO

 OPTION

 

 NETWORK

 

 EASY MENU

 

Item

Description

Using the buttons ▲/▼ corrects the keystone distortion.

Upper in the data Lower in the data

The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well.

KEYSTONE

• When the V:INVERT or the H&V:INVERT is selected under the

 

item MIRROR, if the projector screen is inclined or if the projector is

 

angled downward, this function may not work correctly.

When the zoom adjustment is set to the TELE side, this correction may be excessive. This function should be used with zoom set to WIDE whenever possible.

Using the buttons ▲/▼ turns off/on the whisper mode.

WHISPER

NORMAL WHISPER

• When the WHISPER is selected, acoustic noise and screen

 

 

brightness are reduced.

Using the buttons ▲/▼ switches the mode for mirror status.

MIRROR

NORMAL H:INVERT V:INVERT H&V:INVERT

VOLUME

Using the buttons ▲/▼ adjusts the volume.

High Low

 

 

Choose an input port using the buttons ▲/▼

 AUDIO

 

 

(1), then select the audio port to be interlocked

   QUIT

 

 

with the input port using the buttons ◄/► (2).

  

1   2

 

 RGB1

 

AUDIO

When off is selected, both of two audio ports

 RGB2

 

do not work for the input port.

 S‑VIDEO

 

 

 

 COMPONENT

 

 

 

 VIDEO

 

(1)RGB1 RGB2 COMPONENT S-VIDEO VIDEO

(2)1 2

34

Image 34
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content About contents of package Fastening the lens cover Part names ProjectorCB/PB ComponentCR/PR Control buttons Remote controlMagnify Setting up For the model CP-S245 ArrangementFor the model CP-X255 Adjusting the projectors elevator Using the Security Bar How to attachConnecting your devices About Plug-and-Play capabilityExamples of connection with a computer Examples of connection with a VCR/DVD player Connecting to a monitor outputConnecting to a speaker with amplifier output CB/PBConnecting power supply Remote control Putting batteriesUsing the remote control Turning on the power Power on/offTurning off the power Operating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an input signal Searching an input signalAdjusting the zoom and focus  For a video signal/no signal 43  169  Small For an RGB signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalNo operation, and the projector will enter the Magnify mode Using the magnify featurePress the on button of Magnify on the remote control Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Easy Menu Multifunctional settingsUsing the menu function Advanced MenuEasy Menu Mirror ResetEasy Menu Filter TimePicture Menu GammaColor Temp Picture MenuHigh  Middle  LOW  Custom SecamLOAD1  LOAD2  LOAD3  LOAD4 TV  Film  Turn OFFProgressive SAVE4 SAVE3  SAVE2  SAVE1Over Scan PhaseImage Menu PositionSize Auto AdjustImage Menu ExecuteComponent Input MenuColor Space Video FormatInput Menu InformationVolume Setup MenuAudio OSD Bright Screen MenuMenu Position Bright  DarkMyScreen Screen MenuStart UP MyScreen LockMessage No Input is DetectedAuto Search Reset  CancelOption Menu Auto OFFOption Menu Dhcp Network MenuIP Address Network Menu Refer to the separate volume on Network Functions Network FunctionsLamp MaintenanceLamp Lamp Case of replacement by yourselfType number = DT00731 Air filter Type number = NJ22222Air filtre Replacing Internal Clock battery Page Related messages There is no input signalInternal temperature is rising Is out of the response parameter range of this unitRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeAudio input Communication port SpecificationRGB input Video input Audio outputSpecifications CP-S245/X255 only Controlling the Projector via Scheduling Failure & Warning Alerts via E-mailProjector Management via Snmp Still Image TransferBefore using the network functions… Configuring and controlling the projector via a web browser Configuring and controlling the projector via a web browser Settings Https//192.168.1.10 intoDisplays the Dhcp configuration settings Network InformationDhcp on Network SettingsDisplays and configures network settings Dhcp OFFDisplays and configures communication port settings Port SettingsClick the Apply button to save the settings Mail Settings Displays and configures e-mail addressing settingsAlert Settings Displays and configures failure & warning alertsTemp Error Alert SettingsLamp Error Air Flow ErrorCool Error Lamp Time ErrorFilter Error Schedule Execution Error Other ErrorLamp Time Alarm Change the Lamp is Filter Time AlarmAuthentication Failure DisplayedSchedule Settings Displays and configures schedule settingsSchedule Setting Displays and configures the date and time settings Date/Time SettingsParameter Date/Time Settings SntpSecurity Settings SnmpProjector Control Projector ControlProjector Control Projector Status Displays and configures the current projector statusRestarts the projector’s network connection Network RestartLogoff Description Restart10 Failure & Warning Alerts via E -mailExample If the IP address of the projector is set to Mail Settings Projector management via Snmp Snmp settingsConfigure the following items via a web browser to use Snmp Controlling the Projector via Scheduling Date/Time Settings 18 Date/Time setting can be adjusted via a web browserSchedule Settings 16 Schedule settings can be configured from a web browserCommunication Port Shot Still Image Transfer SettingsShot Still Image Transfer Display Following port is used for e-Shot TCP #9716Shot Still Image Transfer Settings Shot Still Image Transfer TransmissionCommand Control via the Network Command Control Settings 9Command Control Settings 20Header Data RS-232Ccommand Command formatReply Error code Send Data formatReply Data format Authentication Automatic Connection BreakVesa Text Example of computer signalVesa Initial set signals Except when set to RGB OUT Connection to the portsComponent Video C Y, D CB/PB, E CR/PR CTS Audio 1-IN Ø3.5 stereo mini jack, I J Audio 2 L/R RCA jackRTS LAN RJ-45 jackCommunications setting Connecting the cableRS-232C Communication Using the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Keystone Mute OSD Bright Greece